Intel SR1625UR Service Guide - Page 82

Installing and Removing the I/O Expansion Module

Get Intel SR1625UR - Server System - 0 MB RAM PDF manuals and user guides View all Intel SR1625UR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Installing and Removing the I/O Expansion Module Installing the I/O Expansion Module To install the I/O expansion module, follow these steps: 1. Remove the PCI riser assembly. For instructions, see "Removing the PCI Riser Assembly" on page 43. 2. Remove the processor air duct. For instructions, see "Removing the Processor Air Duct" on page 48. 3. Squeeze the sides of the I/O expansion module filler panel(s) to disengage it from the server system back panel and remove it (see letter "A" in Figure 51). Note: If you are installing an I/O expansion module that uses only one slot, remove the filler panel only from the slot shown so that the module can be attached to I/O connector 1. Do not remove the filler panel from the second slot. 4. Attach the standoffs to the server board by pressing into the holes (see letter "B" in Figure 51). Note: For the 1-socket expansion module, install the three standoffs as shown in gray. For the 2socket expansion module, also install the fourth standoff as shown in red. 5. Position the I/O expansion module over the server board as shown in Figure 51. 6. First fit the front of the module into the back panel slot(s), and then attach the module to the server board connector and engage the standoffs (see letter "C" in Figure 51). 64 Intel® Server System SR1625UR Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
64
Intel
®
Server System SR1625UR Service Guide
Installing and Removing the I/O Expansion Module
Installing the I/O Expansion Module
To install the I/O expansion module, follow these steps:
1.
Remove the PCI riser assembly. For instructions, see
“Removing the PCI Riser
Assembly” on page 43
.
2.
Remove the processor air duct. For instructions, see
“Removing the Processor Air
Duct” on page 48
.
3.
Squeeze the sides of the I/O expansion module filler panel(s) to disengage it from
the server system back panel and remove it (see letter “A” in
Figure 51
).
Note:
If you are installing an I/O expansion module that uses only one slot, remove the filler
panel only from the slot shown so that the module can be attached to I/O connector 1. Do
not remove the filler panel from the second slot.
4.
Attach the standoffs to the server board by pressing into the holes (see letter “B” in
Figure 51
).
Note:
For the 1-socket expansion module, install the three standoffs as shown in gray. For the 2-
socket expansion module, also install the fourth standoff as shown in red.
5.
Position the I/O expansion module over the server board as shown in
Figure 51
.
6.
First fit the front of the module into the back panel slot(s), and then attach the
module to the server board connector and engage the standoffs (see letter “C” in
Figure 51
).