Lantronix G520 G520 User Guide - Page 149

PPPoE, PAP/CHAP password

Get Lantronix G520 PDF manuals and user guides View all Lantronix G520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 149 highlights

11: Network Parameters Interface Firewall Settings Create/Assign firewall -zone Description Select the interface to be configured. Select more than one interface, if parameter creating a bridge over multiple interfaces is enabled. Select the firewall zone to be assigned to the interface. Select unspecified - or - create to remove the interface or assign a new zone to the interface respectively. Enter the name of the new zone in the text box and click Save & Apply button. PPPoE Table 11-7 describes the PPPoE protocol settings. Table 11-7 PPPoE Protocol Settings Parameters General Settings Protocol Description PPPoE - Point to Point Protocol over Ethernet Bring up on boot Allows the interface to be live after every reboot. Bring up on boot is checked by default. PAP/CHAP username Enter the PAP/CHAP username. The default password is admin. PAP/CHAP password Access Concentrator Service Name Enter the PAP/CHAP password. Enter the access concentrator name. Enter the service name. Note: Access Concentrator name and Service Name gets auto populated from the PPPoE Access Point router if they are not explicitly provided Advanced Settings Use builtin IPv6 management Force link Allows to use the built in IPv6 management configuration Select this option to assign interface properties regardless of the link being active or not. If not selected, items are assigned only after the link has become active. This is the default. Obtain IPv6-Address Use default gateway Allow IPv6 negotiation on the PPP link Select to use the default gateway. If unselected, no default route will be configured. Use DNS servers advertised by peer Use gateway metric Select to use DNS servers advertised by peer, otherwise ignore advertised DNS servers. Enter gateway metric. LCP echo failure threshold Enter the number of LCP echo request failures allowed before considering the peer dead. Set to zero (0) to ignore failures. LCP echo interval The LCP echo interval in seconds. LCP echo failure threshold must be set, otherwise this value is ignored. Host-Uniq tag content Enter the custom Host-Uniq tag to be used. G520 Series IoT Cellular Gateway User Guide 149

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
11: Network
G520 Series IoT Cellular Gateway User Guide
149
PPPoE
Table 11-7
describes the PPPoE protocol settings.
Table 11-7
PPPoE Protocol Settings
Interface
Select the interface to be configured.
Select more than one interface, if parameter creating a bridge over
multiple interfaces is enabled.
Firewall Settings
Create/Assign firewall -zone
Select the firewall zone to be assigned to the interface.
Select unspecified – or – create to remove the interface or assign a
new zone to the interface respectively.
Enter the name of the new zone in the text box and click Save & Apply
button.
Parameters
Description
General Settings
Protocol
PPPoE – Point to Point Protocol over Ethernet
Bring up on boot
Allows the interface to be live after every reboot.
Bring up on boot is checked by default.
PAP/CHAP username
Enter the PAP/CHAP username. The default password is admin.
PAP/CHAP password
Enter the PAP/CHAP password.
Access Concentrator
Enter the access concentrator name.
Service Name
Enter the service name.
Note:
Access Concentrator name and Service Name gets auto
populated from the PPPoE Access Point router if they are not explicitly
provided
Advanced Settings
Use builtin IPv6 management
Allows to use the built in IPv6 management configuration
Force link
Select this option to assign interface properties regardless of the link
being active or not.
If not selected, items are assigned only after the link has become
active. This is the default.
Obtain IPv6-Address
Allow IPv6 negotiation on the PPP link
Use default gateway
Select to use the default gateway. If unselected, no default route will be
configured.
Use DNS servers advertised by
peer
Select to use DNS servers advertised by peer, otherwise ignore
advertised DNS servers.
Use gateway metric
Enter gateway metric.
LCP echo failure threshold
Enter the number of LCP echo request failures allowed before
considering the peer dead. Set to zero (0) to ignore failures.
LCP echo interval
The LCP echo interval in seconds. LCP echo failure threshold must be
set, otherwise this value is ignored.
Host-Uniq tag content
Enter the custom Host-Uniq tag to be used.
Parameters
Description