Lantronix G520 G520 User Guide - Page 155

WAN and WAN6 Interface, Network > Interface > WAN or WAN6

Get Lantronix G520 PDF manuals and user guides View all Lantronix G520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 155 highlights

11: Network  General Settings - Protocol should be Static Address for the LAN interface. Gateway is not required.  Physical Settings - By default, the LAN interface bridges the eth0.1 and wlan0 physical interfaces.  Firewall Settings - Firewall zone should be set as LAN zone.  DHCP Server - DHCP server can be used to assign IP address to clients connecting to the LAN. To enable the DHCP server, make sure that the check box "Ignore Interface" is not selected, and configure the other DHCP settings. 3. Click Save. 4. Click Save & Apply to save the configuration. WAN and WAN6 Interface Network > Interface > WAN or WAN6 The WAN and WAN6 pages allow you to configure the WAN and WAN6 interfaces, respectively. The WAN interface supports IPv4 or dual mode IPv4/IPv6 and the WAN6 interface supports IPv6 mode. Otherwise, the WAN and WAN6 interfaces are similar and are configured in a similar manner. The WAN or WAN6 interface should use Static Address, DHCP client, DHCPv6 client, or PPPoE protocol. If you assign Static Address as the protocol, the IPv4 gateway is required for the external interface, but should not be used for internal use. DHCP server should be disabled. The interface configuration parameters will depend on the assigned protocol. For descriptions of the protocol settings, see Static Address, DHCP Client, DHCPv6 Client, or PPPoE. To edit the interface: 1. Go to Network > Interfaces, select WAN and click Edit. G520 Series IoT Cellular Gateway User Guide 155

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
11: Network
G520 Series IoT Cellular Gateway User Guide
155
General Settings – Protocol should be Static Address for the LAN interface. Gateway
is not required.
Physical Settings – By default, the LAN interface bridges the eth0.1 and wlan0
physical interfaces.
Firewall Settings – Firewall zone should be set as LAN zone.
DHCP Server – DHCP server can be used to assign IP address to clients connecting
to the LAN. To enable the DHCP server, make sure that the check box "Ignore
Interface" is not selected, and configure the other DHCP settings.
3.
Click
Save
.
4.
Click
Save & Apply
to save the configuration.
WAN and WAN6 Interface
Network > Interface > WAN or WAN6
The WAN and WAN6 pages allow you to configure the WAN and WAN6 interfaces, respectively.
The WAN interface supports IPv4 or dual mode IPv4/IPv6 and the WAN6 interface supports IPv6
mode. Otherwise, the WAN and WAN6 interfaces are similar and are configured in a similar
manner.
The WAN or WAN6 interface should use Static Address, DHCP client, DHCPv6 client, or PPPoE
protocol. If you assign Static Address as the protocol, the IPv4 gateway is required for the external
interface, but should not be used for internal use. DHCP server should be disabled.
The interface configuration parameters will depend on the assigned protocol. For descriptions of
the protocol settings, see
Static Address
,
DHCP Client
,
DHCPv6 Client
, or
PPPoE
.
To edit the interface:
1.
Go to Network > Interfaces, select WAN and click
Edit
.