Marantz SR6004 SR6004 / SR5004 User Manual - English - Page 24

Connecting The Remote Control Jacks, Connecting Other Equipment

Get Marantz SR6004 PDF manuals and user guides View all Marantz SR6004 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

OTHERS TROUBLESHOOTING ADVANCED OPERATION SETUP ADVANCED CONNECTIONS BASIC OPERATION FUNCTIONS CONNECTIONS NAMES AND ENGLISH ADVANCED CONNECTIONS CONNECTING THE REMOTE CONTROL JACKS 2 IN OUT REMOTE CONT. CONNECTING OTHER EQUIPMENT RC OUT IR Receiver FLASHER IN DC OUT BASIC 1 REMOTE CONTROL IN OUT CD recorder EXTERNAL INTERNAL REMOTE CONTROL IN OUT DVD player EXTERNAL INTERNAL REMOTE CONTROL IN OUT CD player EXTERNAL INTERNAL sd a RS-232C Connect an external control device or other device for servicing. (Use a straight cable for the connection.) q You can control other Marantz products through this unit with the remote controller by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote controller is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote control only at the unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier's, power switch is synchronized with this unit's power switch. Set the REMOTE CONTROL SWITCH on the back of other units (not the SR6004/SR5004) to "EXT." (EXTERNAL) to use this feature. 22 w Whenever external infrared sensors or similar devices are connected to REMOTE IN of the unit, be sure to always disable operation of the infrared sensor on the unit by using the following procedure. 1. Hold down the SURROUND MODE button and the MENU button on the front panel at the same time for five seconds. 2. The setting "IR=ENABLE" is shown on the FL DISPLAY. 3. Press the CURSOR buttons (1, 2) to change this to "IR=DISABLE". 4. Press the ENTER button. Once this setting is made, the infrared sensor on the unit is disabled. Note • Be sure to set to "IR=ENABLE" when external infrared sensors or similar devices are not connected. Otherwise, the unit will be unable to receive remote control commands. 5. To restore the original setting, perform steps 1 to 4 to set to "IR=ENABLE". s DC OUT (DC TRIGGER) External devices can be controlled from the unit by connecting them to the DC OUT terminal (12 V 44mA max). GND +12V d FLASHER IN This unit can be controlled by connecting a control box or other control device to this unit. GND Signal RS-232C a

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
NAMES AND
FUNCTIONS
22
BASIC
CONNECTIONS
BASIC
OPERATION
ADVANCED
CONNECTIONS
SETUP
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERS
ADVANCED
CONNECTIONS
ENGLISH
ADVANCED CONNECTIONS
CONNECTING THE REMOTE CONTROL JACKS
IN
IN
OUT
OUT
REMOTE CONT.
REMOTE CONT.
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL
EXTERNAL INTERNAL
EXTERNAL INTERNAL
1
RC OUT
2
DVD player
CD recorder
CD player
IR Receiver
q
You can control other Marantz products through this
unit with the remote controller by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote controller
is received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
control only at the unit. Also, if a Marantz power
amplifier (some models excluded) is connected to
one of these terminals, the power amplifier’s, power
switch is synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the back
of other units (not the SR6004/SR5004) to “EXT.”
(EXTERNAL) to use this feature.
w
Whenever external infrared sensors or similar devices
are connected to REMOTE IN of the unit, be sure to
always disable operation of the infrared sensor on the
unit by using the following procedure.
1.
Hold down the
SURROUND MODE
button
and the
MENU
button on the front panel at
the same time for five seconds.
2.
The setting “IR=ENABLE” is shown on the
FL DISPLAY.
3.
Press the
CURSOR
buttons (
1
,
2
) to change
this to “IR=DISABLE”.
4.
Press the
ENTER
button. Once this setting
is made, the infrared sensor on the unit is
disabled.
Note
• Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not
connected. Otherwise, the unit will be unable to
receive remote control commands.
5.
To restore the original setting, perform
steps
1
to
4
to set to “IR=ENABLE”.
CONNECTING OTHER EQUIPMENT
FLASHER IN
FLASHER IN
DC
DC
OUT
OUT
RS-232C
RS-232C
d
s
a
a
RS-232C
Connect an external control device or other device for
servicing. (Use a straight cable for the connection.)
s
DC OUT (DC TRIGGER)
External devices can be controlled from the unit
by connecting them to the DC OUT terminal (12 V
44mA max).
GND
+12V
d
FLASHER IN
This unit can be controlled by connecting a control
box or other control device to this unit.
GND
Signal