Sony MZ-N707 Operating Instructions - Page 34

ManualRec, REC

Get Sony MZ-N707 - Net MD Walkman Player/Recorder PDF manuals and user guides
UPC - 027242590915
View all Sony MZ-N707 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

4 Press . or > repeatedly until "ManualREC" flashes in the display, and then press ENTER. ManualRec To switch back to the automatic control, Press . or > repeatedly until "Auto REC" flashes in the display, and then press ENTER. 5 Play the source. 6 While observing the level meter in the display, adjust the recording level by pressing . or >. Set the level so that the meter segments light up around the fifth segment (-12 dB) (the center of the level meter) below the display window. If the sound is too high, lower the recording level until the level meter just barely reaches the ninth segment (OVER) below the display window. Volume decreases increases < , REC + To switch back to automatic level control Select "Auto REC" in step 4. Notes • If you press x during recording operation, the recorder will revert to automatic recording level adjustment mode the next time you start a recording operation. • To set the recording level manually during synchro-recording, do the procedure below. 1 Select "SYNC OFF" in step 3 of "Record an MD." (page 19). 2 Do steps 1 to 4 of manual recording procedure. Then do steps 2 and 3, and select "SYNC ON" in the synchro-recording procedure (page 19). Recording starts automatically whenever the source sound is played. • You cannot switch from "Auto REC" to "ManualREC" (or vice-versa) during recording. -12 dB OVER Recording does not start in this step. If your source is an externally connected component, be sure to cue the source to the beginning of the material to be recorded before you start playback. 7 Press X again to start recording. To stop recording Press x. The recording level control is switched back to automatic control when you record the next time. 34-GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
34
-GB
4
Press
.
or
>
repeatedly until
“
ManualREC
”
flashes in the display,
and then press ENTER.
To switch back to the automatic
control, Press
.
or
>
repeatedly until
“
Auto REC
”
flashes
in the display, and then press ENTER.
5
Play the source.
6
While observing the level meter in the
display, adjust the recording level by
pressing
.
or
>
.
Set the level so that the meter
segments light up around the fifth
segment (
–
12 dB) (the center of the
level meter) below the display
window.
If the sound is too high, lower the
recording level until the level meter
just barely reaches the ninth segment
(OVER) below the display window.
Recording does not start in this step.
If your source is an externally
connected component, be sure to cue
the source to the beginning of the
material to be recorded before you
start playback.
7
Press
X
again to start recording.
To stop recording
Press
x
. The recording level control is
switched back to automatic control when you
record the next time.
To switch back to automatic
level control
Select
“
Auto REC
”
in step 4.
Notes
•
If you press
x
during recording operation, the
recorder will revert to automatic recording
level adjustment mode the next time you start
a recording operation.
•
To set the recording level manually during
synchro-recording, do the procedure below.
1
Select
“
SYNC OFF
”
in step 3 of
“
Record an
MD.
”
(page 19).
2
Do steps 1 to 4 of manual recording
procedure. Then do steps 2 and 3, and select
“
SYNC ON
”
in the synchro-recording
procedure (page 19).
Recording starts automatically whenever the
source sound is played.
•
You cannot switch from
“
Auto REC
”
to
“
ManualREC
”
(or vice-versa) during
recording.
ManualRec
<
,
REC
+
Volume
decreases
increases
–
12 dB
OVER