TRENDnet TN-200 User's Guide - Page 57

UBS Devices

Get TRENDnet TN-200 PDF manuals and user guides View all TRENDnet TN-200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

TRENDnet User's Guide To clear the Log, click the Clear button. TN‐200 / TN‐200T1 UBS Devices To activate UPS Settings, go to Management Center, System, and click on USB Devices. Network UPS is a system management feature which uses a local UPS to protect the NAS from an abnormal shutdown. This can be due to a power failure or faulty technology. To enable Network UPS, click the checkbox next to Network UPS. Enter the IP address of the Network UPS Master and click Save to receive the critical power status from the network UPS master. The UPS Status will display the current status of the UPS. Note: Make sure the TN‐200 / TN‐200T1 is on the same network as the network UPS master. If the UPS device is connected to the USB port on the NAS, select either Stand‐ Alone or Master Mode. You will have to enter the IP address(es) of the network UPS slaves to notify them in the event of a power failure. © Copyright 2013 TRENDnet. All Rights Reserved. USB Storage Information: By default, the software shows the USB driver as being un‐ mounted. Ignore this as it changes once you have inserted a USB drive. 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TN
‐
200 / TN
‐
200T1
55
To clear the
Log
, click the
Clear
button.
UBS Devices
To activate
UPS Settings
, go to
Management Center
,
System
, and click on
USB Devices
.
Network UPS is a system management feature which uses a local UPS to protect the NAS
from an abnormal shutdown. This can be due to a power failure or faulty technology. To
enable Network UPS, click the checkbox next to Network UPS. Enter the IP address of
the Network UPS Master and click
Save
to receive the critical power status from the
network UPS master. The UPS Status will display the current status of the UPS.
Note:
Make sure the TN
‐
200 / TN
‐
200T1 is on the same network as the network UPS
master. If the UPS device is connected to the USB port on the NAS, select either Stand
‐
Alone or Master Mode. You will have to enter the IP address(es) of the network UPS
slaves to notify them in the event of a power failure.
USB Storage Information: By default, the software shows the USB driver as being un
‐
mounted. Ignore this as it changes once you have inserted a USB drive.