Yamaha YSP-5600 Owners Manual - Page 30

Using AUTO SETUP IntelliBeam, Turn the unit and your TV on.

Get Yamaha YSP-5600 PDF manuals and user guides View all Yamaha YSP-5600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Using AUTO SETUP (IntelliBeam) • Test tones output during measurement are loud. Perform AUTO SETUP when no children are around and there is no possibility of their entering the listening room, as their hearing may be impaired. • If there are curtains in your listening room, we recommend following the procedure below. 1. Open the curtains to improve sound reflection. 2. Run "Beam optimize only" (p. 32). 3. Close the curtains. 4. Run "Sound optimize only" (p. 32). • Make sure that your listening room is as quiet as possible. For accurate measurement, turn off air conditioner or other devices that make noises. 1 Turn the unit and your TV on. • When a subwoofer is connected to the unit, turn on the subwoofer, and set the volume and crossover frequency as shown below. Set the volume to half Set the crossover frequency to maximum VOLUME CROSSOVER HIGH CUT MIN MAX MIN MAX 2 Switch TV input to display video input from this unit (p. 27). 3 Connect the IntelliBeam microphone to the INTELLIBEAM MIC jack of the unit. INTELLIBEAM MIC INTELLIBEAM MIC IntelliBeam microphone Cardboard microphone stand The screen below is displayed after connecting IntelliBeam microphone to the unit. AUTO SETUP (PREPARATION & CHECK) Please connect the MIC. Please place the MIC at least 1.8m/6ft away from Sound Projector. The MIC should be set at ear level when seated. Measurement takes about 3min. After [ENTER] is pressed, please leave the room. [ENTER]:Start [RETURN]:Cancel "AUTO SETUP" in the "IntelliBeam" menu can automatically adjust the following two settings. Beam optimize only This feature optimizes the beam angle so that the parameter best matches your listening environment. Sound optimize only This feature optimizes sound quality for each channel by measuring the acoustic characteristics of the listening environment. "Beam optimize only" or "Sound optimize only" can be measured separately in the setup menu (p. 32). • Follow the instructions below and then leave the room. If you remain in the room, you may obstruct the beam, or the microphone may pickup any sounds you make, possibly resulting in improper measurement. PREPARATIONS ➤ f Initial settings En 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
PREPARATIONS
➤
f
Initial settings
En
30
•
Test tones output during measurement are loud. Perform AUTO SETUP when no children are around and
there is no possibility of their entering the listening room, as their hearing may be impaired.
•
If there are curtains in your listening room, we recommend following the procedure below.
1.
Open the curtains to improve sound reflection.
2.
Run “Beam optimize only” (p. 32).
3.
Close the curtains.
4.
Run “Sound optimize only” (p. 32).
•
Make sure that your listening room is as quiet as possible. For accurate measurement, turn off air
conditioner or other devices that make noises.
1
Turn the unit and your TV on.
•
When a subwoofer is connected to the unit, turn on the subwoofer, and set the volume and crossover
frequency as shown below.
2
Switch TV input to display video input from this unit (p. 27).
3
Connect the IntelliBeam microphone to the INTELLIBEAM MIC jack
of the unit.
The screen below is displayed after connecting IntelliBeam microphone to the
unit.
“AUTO SETUP” in the “IntelliBeam” menu can automatically adjust the
following two settings.
“Beam optimize only” or “Sound optimize only” can be measured separately in
the setup menu (p. 32).
•
Follow the instructions below and then leave the room. If you remain in the room, you may obstruct
the beam, or the microphone may pickup any sounds you make, possibly resulting in improper
measurement.
Using AUTO SETUP (IntelliBeam)
VOLUME
MIN
MAX
MIN
MAX
CRO
SS
OVER
HIGH CUT
Set the volume to half
Set the crossover frequency to maximum
Beam optimize
only
This feature optimizes the beam angle so that the parameter best
matches your listening environment.
Sound optimize
only
This feature optimizes sound quality for each channel by measuring
the acoustic characteristics of the listening environment.
INTELLIBEAM MIC
INTELLIBEAM MIC
IntelliBeam microphone
Cardboard microphone stand
AUTO SETUP
(PREPARATION & CHECK)
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from Sound Pro-
jector. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel