Yamaha YSP-5600 Owners Manual - Page 33

If an error message is displayed

Get Yamaha YSP-5600 PDF manuals and user guides View all Yamaha YSP-5600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

❑ If an error message is displayed If an error message is displayed on the TV screen, see "Error messages" below to determine the cause and resolve the problem. Follow the instructions displayed on the TV screen to begin measurement again. Error messages ERROR E-1 ERROR E-2 ERROR E-3 ERROR E-4 ERROR E-5 ERROR E-6 ERROR E-7 ERROR E-9 Error message Cause Remedy Please test in quieter environment. There is too much noise in your listening room. Turn off devices, such as an air condition, that make noise, or move the unit away from such devices. You may want to choose certain hours during the day when there is not much noise coming from outside. No MIC detected. Please check MIC connection and re-try. The IntelliBeam microphone is disconnected. Connect the IntelliBeam microphone to the INTELLIBEAM MIC jack on the front of this unit and begin measurement again. Unexpected control is detected. Please re-try. Some other operations were performed on this unit. Begin measurement again. Do not perform any other operations with this unit during measurement. Please check MIC position. MIC should be set in front of Sound Projector. Please re-try. The IntelliBeam microphone is not placed in front of this unit. Position the IntelliBeam microphone in front of this unit and begin measurement again. Please check MIC position. MIC should be set above 1.8m/ The IntelliBeam microphone is not placed in the right distance 6.0ft and re-try. from this unit. Position the IntelliBeam microphone at a distance of more than 1.8 m (6.0 ft) from this unit and begin measurement again. Volume level is lower than expected. Please check MIC position/connection and re-try. The IntelliBeam microphone cannot collect the sound produced by this unit. Position the IntelliBeam microphone properly, check the connection, and then begin measurement again. Unexpected error happened. Please turn off and re-try. An internal system error occurred. Press the z key to turn off this unit, then run AUTO SETUP procedure again after turning this unit on. Please check the connection with subwoofer. The subwoofer output signals cannot be recognized. Confirm the connection between the wireless subwoofer kit and subwoofer (p. 25), and begin measurement again. PREPARATIONS ➤ f Initial settings En 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
PREPARATIONS
➤
f
Initial settings
En
33
❑
If an error message is displayed
If an error message is displayed on the TV screen, see “Error messages” below to determine the cause and resolve the problem. Follow the instructions displayed on the TV screen
to begin measurement again.
Error messages
Error message
Cause
Remedy
ERROR E-1
Please test in quieter environment.
There is too much noise in your listening room.
Turn off devices, such as an air condition, that make noise, or
move the unit away from such devices.
You may want to choose certain hours during the day when
there is not much noise coming from outside.
ERROR E-2
No MIC detected. Please check MIC connection and re-try.
The IntelliBeam microphone is disconnected.
Connect the IntelliBeam microphone to the INTELLIBEAM
MIC jack on the front of this unit and begin measurement
again.
ERROR E-3
Unexpected control is detected. Please re-try.
Some other operations were performed on this unit.
Begin measurement again. Do not perform any other
operations with this unit during measurement.
ERROR E-4
Please check MIC position. MIC should be set in front of
Sound Projector. Please re-try.
The IntelliBeam microphone is not placed in front of this unit.
Position the IntelliBeam microphone in front of this unit and
begin measurement again.
ERROR E-5
Please check MIC position. MIC should be set above 1.8m/
6.0ft and re-try.
The IntelliBeam microphone is not placed in the right distance
from this unit.
Position the IntelliBeam microphone at a distance of more
than 1.8 m (6.0 ft) from this unit and begin measurement
again.
ERROR E-6
Volume level is lower than expected. Please check MIC
position/connection and re-try.
The IntelliBeam microphone cannot collect the sound
produced by this unit.
Position the IntelliBeam microphone properly, check the
connection, and then begin measurement again.
ERROR E-7
Unexpected error happened. Please turn off and re-try.
An internal system error occurred.
Press the
z
key to turn off this unit, then run AUTO SETUP
procedure again after turning this unit on.
ERROR E-9
Please check the connection with subwoofer.
The subwoofer output signals cannot be recognized.
Confirm the connection between the wireless subwoofer kit
and subwoofer (p. 25), and begin measurement again.