Home » ZyXEL Manuals » Networking » ZyXEL G-220 » Manual Viewer

ZyXEL G-220 User Guide - Page 40

On a computer connected to the wireless client, try to connect to the Internet. If you can

Get ZyXEL G-220 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

ZyXEL G-220 v2 User's Guide When you use the PIN method, you must enter the PIN from one device (usually the wireless client) into the second device (usually the Access Point or wireless router). Then, when WPS is activated on the first device, it presents its PIN to the second device. If the PIN matches, one device sends the network and security information to the other, allowing it to join the network. Take the following steps to set up a WPS connection between an access point or wireless router (referred to here as the AP) and a client device using the PIN method. 1 Ensure WPS is enabled on both devices. 2 Access the WPS section of the AP's configuration interface. See the device's User's Guide for how to do this. 3 Look for the client's WPS PIN; it will be displayed either on the device, or in the WPS section of the client's configuration interface (see the device's User's Guide for how to find the WPS PIN - for the G-220 v2, see Section 3.3.1 on page 39). 4 Enter the client's PIN in the AP's configuration interface. Note: If the client device's configuration interface has an area for entering another device's PIN, you can either enter the client's PIN in the AP, or enter the AP's PIN in the client - it does not matter which. 5 Start WPS on both devices within two minutes. Note: Use the configuration utility to activate WPS, not the push-button on the device itself. 6 On a computer connected to the wireless client, try to connect to the Internet. If you can connect, WPS was successful. If you cannot connect, check the list of associated wireless clients in the AP's configuration utility. If you see the wireless client in the list, WPS was successful. The following figure shows a WPS-enabled wireless client (installed in a notebook computer) connecting to the WPS-enabled AP via the PIN method. 40 Chapter 3 Wireless LAN Network

Section	Page
User’s Guide	1
About This User's Guide	3
Document Conventions	4
Safety Warnings	6
Copyright	7
Certifications	8
ZyXEL Limited Warranty	10
Table of Contents	11
List of Figures	15
List of Tables	19
Getting Started	21
1.1 About Your G-220 v2	21
1.2 Application Overview	21
1.2.1 Windows Vista Users	21
1.2.2 Station Mode	21
1.2.2.1 Infrastructure	21
1.2.2.2 Ad-Hoc	22
1.2.3 Access Point Mode	23
1.2.4 Changing G-220 v2 Mode	23
1.3 G-220 v2 Hardware and Utility Installation	24
1.3.1 ZyXEL Utility Icon	24
1.4 Configuration Methods	24
1.4.1 Enabling WZC	24
1.4.2 Accessing the ZyXEL Utility	25
Tutorial	27
2.1 Connecting to a Wireless LAN	27
2.2 Creating and Using a Profile	29
2.3 Configuring the G-220 v2 as an AP	32
Wireless LAN Network	35
3.1 Wireless LAN Overview	35
3.2 Wireless LAN Security	36
3.2.1 Hide SSID	36
3.2.2 MAC Address Filter	36
3.2.3 User Authentication and Encryption	37
3.2.3.1 WEP	37
3.2.3.2 IEEE 802.1x	38
3.2.3.3 WPA and WPA2	38
3.3 WiFi Protected Setup	39
3.3.1 Push Button Configuration	39
3.3.2 PIN Configuration	39
3.3.3 How WPS Works	41
3.3.3.1 Example WPS Network Setup	42
3.3.4 Limitations of WPS	44
3.4 Introduction to OTIST	45
3.4.1 Enabling OTIST	45
3.4.1.1 AP	45
3.4.1.2 Wireless Client	46
3.4.2 Starting OTIST	47
3.4.3 Notes on OTIST	47
Wireless Station Mode Configuration	49
4.1 Wireless Station Mode Overview	49
4.1.1 ZyXEL Utility Screen Summary	49
4.2 The Link Info Screen	50
4.2.1 Trend Chart	51
4.3 The Site Survey Screen	52
4.3.1 Security Settings	53
4.3.1.1 WEP Encryption	54
4.3.1.2 WPA-PSK/WPA2-PSK	55
4.3.1.3 WPA/WPA2	56
4.3.1.4 IEEE 802.1x	57
4.3.2 Confirm Save Screen	59
4.4 The Profile Screen	60
4.4.1 Adding a New Profile	62
4.5 The Adapter Screen	66
4.6 Security Settings in Windows Vista	69
4.6.1 Using PEAP in Vista	69
4.6.2 Using TLS in Vista	70
Access Point Mode Configuration	73
5.1 Access Point Mode Introduction	73
5.1.1 ZyXEL Utility Screen Summary	73
5.1.2 Additional Setup Requirements	74
5.2 The Link Info Screen	74
5.3 The Configuration Screen	75
5.4 The MAC Filter Screen	77
Maintenance	79
6.1 The About Screen	79
6.2 Uninstalling the ZyXEL Utility	79
6.3 Upgrading the ZyXEL Utility	80
Troubleshooting	83
7.1 Problems Starting the ZyXEL Utility	83
7.2 Problem Connecting to an Access Point	83
7.3 Problem with the Link Quality	84
7.4 Problems Communicating With Other Computers	84
Product Specifications	85
Access Point Mode Setup Example	87
Configuring the Computer on Which You Install the G-220 v2	87
Configuring the Wireless Station Computer	89
Management with Wireless Zero Configuration	91
Activating Wireless Zero Configuration	91
Connecting to a Wireless Network	92
Security Settings	95
Association	96
Authentication	97
Ordering the Preferred Networks	100
Wireless Security	103
Types of EAP Authentication	103
EAP-MD5 (Message-Digest Algorithm 5)	103
EAP-TLS (Transport Layer Security)	104
EAP-TTLS (Tunneled Transport Layer Service)	104
PEAP (Protected EAP)	104
LEAP	104
Dynamic WEP Key Exchange	104
WPA and WPA2	105
Encryption	105
User Authentication	106
WPA(2)-PSK Application Example	107
WPA(2) with RADIUS Application Example	107
Security Parameters Summary	108
Setting up Your Computer’s IP Address	109
Windows 95/98/Me	109
Installing Components	110
Configuring	111
Verifying Settings	112
Windows 2000/NT/XP	112
Verifying Settings	116
Macintosh OS 8/9	116
Verifying Settings	118
Macintosh OS X	118
Verifying Settings	119
Customer Support	121

Match case Limit results 1 per page

ZyXEL G-220 v2 User’s Guide

Chapter 3 Wireless LAN Network

When you use the PIN method, you must enter the PIN from one device (usually the wireless

client) into the second device (usually the Access Point or wireless router). Then, when WPS

is activated on the first device, it presents its PIN to the second device. If the PIN matches, one

device sends the network and security information to the other, allowing it to join the network.

Take the following steps to set up a WPS connection between an access point or wireless

router (referred to here as the AP) and a client device using the PIN method.

Ensure WPS is enabled on both devices.

Access the WPS section of the AP’s configuration interface. See the device’s User’s

Guide for how to do this.

Look for the client’s WPS PIN; it will be displayed either on the device, or in the WPS

section of the client’s configuration interface (see the device’s User’s Guide for how to

find the WPS PIN - for the G-220 v2, see

Section 3.3.1 on page 39

Enter the client’s PIN in the AP’s configuration interface.

Note:

If the client device’s configuration interface has an area for entering another

device’s PIN, you can either enter the client’s PIN in the AP, or enter the AP’s

PIN in the client - it does not matter which.

Start WPS on both devices within two minutes.

Note:

Use the configuration utility to activate WPS, not the push-button on the device

itself.

On a computer connected to the wireless client, try to connect to the Internet. If you can

connect, WPS was successful.

If you cannot connect, check the list of associated wireless clients in the AP’s

configuration utility. If you see the wireless client in the list, WPS was successful.

The following figure shows a WPS-enabled wireless client (installed in a notebook computer)

connecting to the WPS-enabled AP via the PIN method.