ZyXEL P-128 User Guide - Page 116

Dial-In Users Setup

Get ZyXEL P-128 PDF manuals and user guides View all ZyXEL P-128 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 116 highlights

Prestige 128IMH ISDN Modem/ Router/Hub 8.3.1 Default Dial-in Filter Use Menu 13.1 - Default Dial-in Filter to specify the filter set(s) to apply to the incoming and outgoing traffic between all dial-in users and your Prestige. Note that the filter set(s) only applies to the dial-in users but not the remote nodes. You can specify up to 4 filter sets separated by comma, e.g., 1, 5, 9, 12, in each of the filters field. The default is no filters. Spaces are accepted in this field. For more information on defining the filters, see Chapter 9. Menu 13.1 - Default Dial -in Filter Input F ilter Sets: protocol filters= Figure 8-4 Default Dial-in Filter 8.4 Dial-In Users Setup The following steps describe the setup procedure for setting up a remote dial-in user. Step 1. From the Main Menu, enter option 14 to go to Menu 14 - Dial-in User Setup, as shown in the figure below. Figure 8-5 Menu 14 - Dial-in User Setup 8-8 Dial-In Server Configuration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
Prestige
128IMH ISDN Modem/ Router/Hub
8-8
Dial-In Server Configuration
8.3.1 Default Dial-in Filter
Use
Menu 13.1 – Default Dial-in Filter
to specify the filter set(s) to apply to the incoming
and outgoing traffic between all dial-in users and your Prestige.
Note that the filter set(s) only
applies to the dial-in users but not the remote nodes.
You can specify up to 4 filter sets
separated by comma, e.g., 1, 5, 9, 12, in each of the
filters
field.
The default is no filters.
Spaces are accepted in this field.
For more information on defining the filters,
see Chapter 9
.
Figure 8-4 Default Dial-in Filter
8.4
Dial-In Users Setup
The following steps describe the setup procedure for setting up a remote dial-in user.
Step 1.
From the Main Menu, enter option 14 to go to Menu 14 - Dial-in User Setup, as
shown in the figure below.
Figure 8-5 Menu 14 - Dial-in User Setup
Menu 13.1 - Default Dial-in Filter
Input Filter Sets:
protocol filters=