Audiovox NAV102 Operation Manual - Page 35

<[ENsEB&gt - navigation module

Get Audiovox NAV102 PDF manuals and user guides View all Audiovox NAV102 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

i i " J'~ " _- ..... I" .~ ~ , j ..........: '. .= < :. Parts List ./ NAV102 navigation module ./ Antenna with magnetic mount ./ Four rubber feet (to affix to the bottom of the NAV102 in the recessed area near each corner) ./ SmartBus cable (used to connect the NAV102 to the Jensen navigation-ready radio) ./ One 2 Gigabyte SO Card pre loaded with map/navigation software ./ Two 11 mm (.4in) screws (for fastening the SmartBus cable to the radio and NAV102) ./ OVO with backup software for map data and navigation Warnings • Do not install components in areas which are susceptible to rain, moisture, direct sunlight, extreme heat or cold, excessive dust, dirt or humidity. • Do not install the NAV102 where it will obstruct the driver's view or interfere with the vehicle's operating system or safety features (air bags, hazard light buttons, etc.). • Use only installation parts and hardware provided with the unit. Use of other parts can cause malfunction and possible damage to your navigation system. • This product should only be installed in vehicles with a 12-volt battery with negative grounding. Check the battery voltage of your vehicle before installation. • Be sure to secure all wires/cables safely away from the steering wheel, shift lever, and gas or brake pedal. • Do not cut the GPS antenna cable to shorten or lengthen it. NAV102 Placement The NAV102 should be installed under the back or front seat. It can also be installed in the trunk, if necessary. Do not install the NAV102 where it will come in contact with water or direct sunlight. To avoid shorts in the electrical system, be sure to disconnect the negative (-) battery cable before beginning installation. NOTE: Be sure to install the NAV102 in such a way that the SO card slot is accessible after install, allowing for the removal and insertion of the SO card for future changes to map data or upgrades. Compatible Head Units VM9212N VM9213 VM9223 VM9312HO VM9313 VM9412 VM9413 VM9423 VM9512 VM9512HO VM9022 VM9022HO 1\DV E'\J AMM10N AMM12N ~c={E!l~1S LINEAR SERIES UV9 PIN: 127070005188

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
To
avoid
shorts
in the electrical system, be sure
to
disconnect
the negative
(-)
battery cable before
beginning installation.
NAV102 Placement
The NAV102 should be installed under the back or front
seat. It can also be installed
in
the trunk,
if
necessary. Do
not install the NAV102 where it will come
in
contact with
water or direct sunlight.
PIN:
127070005188
UV9
~c={E!l~1S
LINEAR
SERIES
Compatible
Head
Units
1\
DV
E'\J
AMM10N
AMM12N
<[ENsEB>
VM9212N
VM9413
VM9213
VM9423
VM9223
VM9512
VM9312HO
VM9512HO
VM9313
VM9022
VM9412
VM9022HO
NOTE:
Be sure to install
the NAV102
in
such a way
that the
SO
card slot is
accessible after
install, allowing
for the removal
and insertion
of
the
SO
card
for future
changes to
map data or
upgrades.
Parts List
./
NAV102 navigation module
./
Antenna with magnetic mount
./
Four rubber feet (to affix to the bottom of the NAV102
in
the recessed area near each corner)
./
SmartBus cable (used to connect the NAV102 to the
Jensen navigation-ready radio)
./
One 2 Gigabyte
SO
Card pre loaded with
map/navigation software
./
Two
11
mm (.4in) screws (for fastening the SmartBus
cable to the radio and NAV102)
./
OVO
with backup software for map data and
navigation
Warnings
•
Do not install components
in
areas which are
susceptible to rain, moisture, direct sunlight, extreme
heat or cold, excessive dust, dirt or humidity.
•
Do not install the NAV102 where it will obstruct the
driver's view or interfere with the vehicle's operating
system or safety features (air bags, hazard light
buttons, etc.).
•
Use only installation parts and hardware provided with
the unit. Use of other parts can cause malfunction and
possible damage to your navigation system.
•
This product should only be installed
in
vehicles with
a 12-volt battery with negative grounding. Check the
battery voltage
of
your vehicle before installation.
•
Be sure to secure all wires/cables safely away from
the steering wheel, shift lever, and gas or brake pedal.
•
Do not cut the GPS antenna cable to shorten
or
lengthen
it.
i
i
"
J'~
"
.....
_-
I"
.~
~
,
j
..........
:
'.
.=
<
:.