Compaq AP550 Compaq Professional Workstation AP550 Maintenance & Service G - Page 40

Subpanel and Bezel Blanks, Remove the front bezel.

Get Compaq AP550 - Professional - 128 MB RAM PDF manuals and user guides
UPC - 743172976857
View all Compaq AP550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Removal and Replacement Procedures 3-7 Subpanel and Bezel Blanks NOTE: The subpanel and bezel blanks must be removed from the front bezel if you are installing a mass storage device for the first time, or if you are converting the unit from a minitower to a desktop configuration or from a desktop to a minitower configuration. To remove the bezel blank from the front bezel: 1. Perform the steps in the "Service Preparations" section as previously shown. CAUTION: Before removing the workstation access panel, ensure that the workstation is turned off, all cables are disconnected from the back of the workstation, and the power cord is disconnected from the grounded AC outlet. 2. Remove the side workstation access panel. 3. Remove the front bezel. 4. Gently pull the subpanel, with the bezel blank secured in it, away from the front bezel, and then remove the bezel blank. CAUTION: Hold the subpanel straight when you pull it away from the front bezel. Pulling at an angle could damage the pins that align the subpanel within the front bezel. Figure 3-6. Removing the subpanel and bezel blanks To replace the subpanel and bezel blanks, reverse the above procedure. Be sure the subpanel and front bezel align properly with the alignment tabs. See Figure 3-7 for the subpanel keyed-alignment positions. NOTE: When switching from minitower to desktop orientation, the bezel blank should be switched out with the replacement provided to ensure that the Compaq logo is properly oriented.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
Removal and Replacement Procedures
3-7
Subpanel and Bezel Blanks
NOTE:
The subpanel and bezel blanks must be removed from the front bezel if you are installing a
mass storage device for the first time, or if you are converting the unit from a minitower to a desktop
configuration or from a desktop to a minitower configuration.
To remove the bezel blank from the front bezel:
1.
Perform the steps in the “Service Preparations” section as previously shown.
CAUTION:
Before removing the workstation access panel, ensure that the workstation is
turned off, all cables are disconnected from the back of the workstation, and the power cord is
disconnected from the grounded AC outlet.
2.
Remove the side workstation access panel.
3.
Remove the front bezel.
4.
Gently pull the subpanel, with the bezel blank secured in it, away from the front bezel, and
then remove the bezel blank.
CAUTION:
Hold the subpanel straight when you pull it away from the front bezel. Pulling at an
angle could damage the pins that align the subpanel within the front bezel.
Figure 3-6.
Removing the subpanel and bezel blanks
To replace the subpanel and bezel blanks, reverse the above procedure. Be sure the subpanel and
front bezel align properly with the alignment tabs. See Figure 3-7 for the subpanel
keyed-alignment positions.
NOTE:
When switching from minitower to desktop orientation, the bezel blank should be switched out
with the replacement provided to ensure that the Compaq logo is properly oriented.