Compaq ProLiant 6400R Compaq ProLiant 6400R Setup and Installation Guide - Page 105

Securing the Power Cord

Get Compaq ProLiant 6400R PDF manuals and user guides View all Compaq ProLiant 6400R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

Cabling Guidelines 6-7 IMPORTANT: The system power in the ProLiant 6400R does not completely shut off with the front panel Power On/Standby switch. The two positions of the switch function as On and Standby, rather than On and Off. The Standby position removes power from most of the electronics and the drives but portions of the power supply and some internal circuitry remain active. Consequently, to remove all power from the system, disconnect the power cord from the server. In systems with multiple power supplies, you must disconnect all the power cords to completely remove power from the system. Securing the Power Cord Plug in the power cord. If desired, tie wrap the AC power cord to the plastic loop provided on the power supply. Leave an 8-inch service loop for the plug to prevent the plug from accidentally being disengaged. The following figure identifies the location for both power cords: the primary power supply and the secondary power supply . 2 1 Figure 6-4. Securing the AC power cord to the service loop

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Cabling Guidelines
6-7
IMPORTANT:
The system power in the ProLiant 6400R does not completely shut off with
the front panel Power On/Standby switch. The two positions of the switch function as On
and Standby, rather than On and Off. The Standby position removes power from most of
the electronics and the drives but portions of the power supply and some internal circuitry
remain active.
Consequently, to remove all power from the system, disconnect the power cord from the
server. In systems with multiple power supplies, you must disconnect all the power cords
to completely remove power from the system.
Securing the Power Cord
Plug in the power cord. If desired, tie wrap the AC power cord to the plastic
loop provided on the power supply. Leave an 8-inch service loop for the plug
to prevent the plug from accidentally being disengaged. The following figure
identifies the location for both power cords: the primary power supply
and
the secondary power supply
.
2
1
Figure 6-4.
Securing the AC power cord to the service loop