Compaq ProLiant 6400R Compaq ProLiant 6400R Setup and Installation Guide - Page 58

Appendix C, Switch Settings., Install the PPM

Get Compaq ProLiant 6400R PDF manuals and user guides View all Compaq ProLiant 6400R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Installing Hardware Options 3-5 CAUTION: Always fully loosen the terminator module retention screw to avoid possible damage to the processor. 10. Remove the terminator module from the selected socket: a. Fully loosen the terminator module retention screw . b. Open the ejector levers . c. Pull the terminator module out of its socket and keep for future use. 2 2 1 3 Figure 3-3. Removing the processor terminator module from the processor socket CAUTION: If you remove a processor, reinstall the processor terminator module before powering up the server. Failure to have either a processor or processor terminator module installed results in an interlock fault condition that prevents the server from powering up. 11. Locate the core frequency switch for the processor socket and set the processor core frequency switch to the appropriate setting. See Appendix C, "Switch Settings." 12. Install the PPM: a. Align the new PPM with the PPM socket. b. Install and secure the processor power module by pushing it into the socket . c. Rotate the ejector levers inward until the board fully seats into the socket.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Installing Hardware Options
3-5
CAUTION:
Always fully loosen the terminator module retention screw to avoid
possible damage to the processor.
10.
Remove the terminator module from the selected socket:
a.
Fully loosen the terminator module retention screw
.
b.
Open the ejector levers
.
c.
Pull the terminator module out of its socket
and keep for future
use.
1
2
2
3
Figure 3-3.
Removing the processor terminator module from the
processor socket
CAUTION:
If you remove a processor, reinstall the processor terminator module
before powering up the server. Failure to have either a processor or processor
terminator module installed results in an interlock fault condition that prevents
the server from powering up.
11.
Locate the core frequency switch for the processor socket and set the
processor core frequency switch to the appropriate setting. See
Appendix C, “Switch Settings.”
12.
Install the PPM:
a.
Align the new PPM with the PPM socket.
b.
Install and secure the processor power module by pushing it into the
socket
.
c.
Rotate the ejector levers inward
until the board fully seats into the
socket.