Compaq ProLiant 6400R Compaq ProLiant 6400R Setup and Installation Guide - Page 56

Installing a Processor and Processor Power Module (PPM)

Get Compaq ProLiant 6400R PDF manuals and user guides View all Compaq ProLiant 6400R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Installing Hardware Options 3-3 Installing a Processor and Processor Power Module (PPM) The ProLiant 6400R server ships with at least one processor, one Processor Power Module (PPM) installed, and up to three processor terminator modules. The server can support up to four processors and four PPMs. 1 2 Figure 3-1. Processor and Processor Power Module To install a processor and a PPM , use the following installation procedure: 1. Back up the server data. 2. Shut down the operating system as directed in the operating system instructions. 3. If the server is on, set the power switch to standby. 4. Verify that the first system LED on the front panel, located nearest the Power On/Standby switch, turns off and that all fans stop spinning. WARNING: Before removing the top access panel, be sure that the power switch is in the standby position and that the power cord is disconnected from the electrical outlet.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Installing Hardware Options
3-3
Installing a Processor and Processor Power
Module (PPM)
The ProLiant 6400R server ships with at least one processor, one Processor
Power Module (PPM) installed, and up to three processor terminator modules.
The server can support up to four processors and four PPMs.
1
2
Figure 3-1.
Processor
and Processor Power Module
To install a processor
and a PPM
, use the following installation
procedure:
1.
Back up the server data.
2.
Shut down the operating system as directed in the operating system
instructions.
3.
If the server is on, set the power switch to standby.
4.
Verify that the first system LED on the front panel, located nearest the
Power On/Standby switch, turns off and that all fans stop spinning.
WARNING:
Before removing the top access panel, be sure that the power
switch is in the standby position and that the power cord is disconnected from
the electrical outlet.