Compaq ProLiant 6400R Compaq ProLiant 6400R Setup and Installation Guide - Page 46

Attaching Handles to the Server, Installing the Server into the Rack

Get Compaq ProLiant 6400R PDF manuals and user guides View all Compaq ProLiant 6400R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

2-18 Compaq ProLiant 6400R Setup and Installation Guide Attaching Handles to the Server 1. Align the rack mounting handles on the side of the server. 2. Attach the rack mounting handles with screws. IMPORTANT: Your server may vary from the one shown in Figure 2-10. However, the process of attaching the handles to the server is the same. Figure 2-9. Attaching rack mounting handles to the server Installing the Server into the Rack Load and secure the server to the rack with the face plate thumb screws before attaching any more mounting bracket assemblies. Ensure that the pair of brackets is perfectly aligned and installed and that the server fits before you continue. WARNING: To reduce the risk of personal injury or damage to the equipment, a minimum of two people MUST lift the server into the rack. The server may weigh 75 lb (34 kg). If the unit is to be loaded above chest level, a third person MUST assist in aligning the rails while the other two support the unit. IMPORTANT: To reduce the weight of the server and make it more manageable, do not install drives until after you load the server into the rack. 1. Pull the slide rails forward from the mounting brackets to a fully extended position. 2. Set the server handles on the extended slide rails.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
2-18
Compaq ProLiant 6400R Setup and Installation Guide
Attaching Handles to the Server
1.
Align the rack mounting handles on the side of the server.
2.
Attach the rack mounting handles with screws.
IMPORTANT:
Your server may vary from the one shown in Figure 2-10. However, the
process of attaching the handles to the server is the same.
Figure 2-9.
Attaching rack mounting handles to the server
Installing the Server into the Rack
Load and secure the server to the rack with the face plate thumb screws before
attaching any more mounting bracket assemblies. Ensure that the pair of
brackets is perfectly aligned and installed and that the server fits before you
continue.
WARNING:
To reduce the risk of personal injury or damage to the equipment, a
minimum of two people
MUST
lift the server into the rack. The server may
weigh 75 lb (34 kg). If the unit is to be loaded above chest level, a third person
MUST
assist in aligning the rails while the other two support the unit.
IMPORTANT:
To reduce the weight of the server and make it more manageable, do not
install drives until after you load the server into the rack.
1.
Pull the slide rails forward from the mounting brackets to a fully
extended position.
2.
Set the server handles on the extended slide rails.