Compaq ProLiant 6400R Compaq ProLiant 6400R Setup and Installation Guide - Page 78

Removing Hot-Plug Hard Drives, CAUTION, WARNING

Get Compaq ProLiant 6400R PDF manuals and user guides View all Compaq ProLiant 6400R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Installing Hardware Options 3-25 CAUTION: Make sure that the ejector levers are properly seated. 5. Place the hot-plug SCSI hard drive online as directed by the operating system instructions. If the drive was replaced, the array controller automatically activates the drive and starts rebuilding the data. Removing Hot-Plug Hard Drives Use the following procedure to remove hot-plug hard drives: 1. Locate the hot-plug hard drive to be removed from the drive bay. 2. Push the release button . 3. Pull the release lever and pull the drive toward the front of the server to remove the hot-plug hard drive. 3 1 2 1 Figure 3-22. Removing a hot-plug drive 4. Insert a blanking panel into the empty drive bay, pushing until seated. WARNING: Hazardous energy levels cause a risk of personal injury or damage to equipment. The installation of options and routine maintenance and service of this product must be performed by persons knowledgeable about the procedures, precautions, and hazards associated with equipment containing hazardous energy circuits.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Installing Hardware Options
3-25
CAUTION:
Make sure that the ejector levers are properly seated.
5.
Place the hot-plug SCSI hard drive online as directed by the operating
system instructions. If the drive was replaced, the array controller
automatically activates the drive and starts rebuilding the data.
Removing Hot-Plug Hard Drives
Use the following procedure to remove hot-plug hard drives:
1.
Locate the hot-plug hard drive to be removed from the drive bay.
2.
Push the release button
.
3.
Pull the release lever
and pull the drive toward the front of the server
to remove the hot-plug hard drive.
2
3
1
1
Figure 3-22.
Removing a hot-plug drive
4.
Insert a blanking panel into the empty drive bay, pushing until seated.
WARNING:
Hazardous energy levels cause a risk of personal injury or damage
to equipment. The installation of options and routine maintenance and service of
this product must be performed by persons knowledgeable about the
procedures, precautions, and hazards associated with equipment containing
hazardous energy circuits.