Compaq ProLiant 8000 ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maint - Page 172

The following ASR-2 flow chart shows the sequence of events after a hardware or software

Get Compaq ProLiant 8000 PDF manuals and user guides View all Compaq ProLiant 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 172 highlights

Diagnostics and Troubleshooting 3-75 The following ASR-2 flow chart shows the sequence of events after a hardware or software error occurs. Hardware/Software error occurs. | Error is recorded in the Critical Error Log or the Integrated Management Log, depending on the server configuration. | Operating system halts normal operation. | ASR timer expires. | Server is reset. | If a modem is installed and paging is enabled, the Server Failure Notification pager alert is sent to the Server Administrator. | Unattended server starts the operating system. ---Or--- Server starts Compaq Utilities from the system partition on the hard drive.  If the server continues to experience hardware/software errors and the number of ASR cycles exceeds the specified number of recovery attempts, the server logs an error to the Server Health Log or the Integrated Management Log and boots the Compaq Utilities from the system partition on the hard drive. | If a modem is installed, ASR puts the modem on autoanswer so that the server administrator can dial in (using third-party terminal emulator software) to remotely run the Compaq Utilities to identify the source of the fault. | Or | Local Server Administrator runs Compaq Utilities from the server console to identify the source of the fault. Figure 3-1. ASR-2 flow chart

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
Diagnostics and Troubleshooting
3-75
The following ASR-2 flow chart shows the sequence of events after a hardware or software
error occurs.
Hardware/Software error occurs.
|
Error is recorded in the Critical Error
Log or the Integrated Management
Log, depending on the server
configuration.
|
Operating system halts normal
operation.
|
ASR timer expires.
|
Server is reset.
|
If a modem is installed and paging is
enabled, the Server Failure
Notification pager alert is sent to the
Server Administrator.
|
Unattended server starts the
operating system.
---Or---
Server starts Compaq Utilities from
the system partition on the
hard drive.
|
If the server continues to experience
hardware/software errors and the
number of ASR cycles exceeds the
specified number of recovery
attempts, the server logs an error to
the Server Health Log or the
Integrated Management Log and
boots the Compaq Utilities from the
system partition on the hard drive.
If a modem is installed, ASR puts
the modem on autoanswer so that
the server administrator can dial in
(using third-party terminal emulator
software) to remotely run the
Compaq Utilities to identify the
source of the fault.
|
Or
|
Local Server Administrator runs
Compaq Utilities from the server
console to identify the source of
the fault.
Figure 3-1.
ASR-2 flow chart