Compaq ProLiant 8000 ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maint - Page 86

Push the slot release lever inward to lock the rear of the controller into position

Get Compaq ProLiant 8000 PDF manuals and user guides View all Compaq ProLiant 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Removal and Replacement Procedures 2-69 To replace an array controller with Extended SCSI: 1. Line up the controller with the appropriate slot . 2. Push the controller into the bus slot. NOTE: Seat the controller into the slot using the ejector levers to ensure complete board connection. 3. Press the ejector levers inward to lock the long side of the control board into position . 4. Push the slot release lever inward to lock the rear section of the controller into position . NOTE: An audible click should occur, indicating that the controller is fully seated. 2 3 1 Figure 2-60. Replacing an array controller with Extended SCSI

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
Removal and Replacement Procedures
2-69
To replace an array controller with Extended SCSI:
1.
Line up the controller with the appropriate slot
.
2.
Push the controller into the bus slot.
NOTE:
Seat the controller into the slot using the ejector levers to ensure complete board connection.
3.
Press the ejector levers inward to lock the long side of the control board into position
.
4.
Push the slot release lever inward to lock the rear section of the controller into position
.
NOTE:
An audible click should occur, indicating that the controller is fully seated.
1
2
3
Figure 2-60.
Replacing an array controller with Extended SCSI