Dell OptiPlex 7000 Small Form Factor Service Manual - Page 10

Removing and installing components, Recommended tools, Screw list

Get Dell OptiPlex 7000 Small Form Factor PDF manuals and user guides View all Dell OptiPlex 7000 Small Form Factor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

2 Removing and installing components NOTE: The images in this document may differ from your computer depending on the configuration you ordered. Recommended tools The procedures in this document may require the following tools: ● Phillips screwdriver #0 ● Phillips screwdriver #1 ● Plastic scribe Screw list NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is restored when the component is replaced. NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surfaces when replacing a component. NOTE: Screw color may vary with the configuration ordered. Table 1. Screw list Component Solid-state drive Screw type M2x3 Quantity 1 Screw image Hard-drive and optical-drive #6-32 2 supporting bracket SD-card reader M3x5 1 WLAN card M2x3 1 Processor-fan and heat-sink Captive 4 assembly Voltage regulator heat-sink Captive 4 Power-supply unit #6-32 3 10 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Removing and installing components
NOTE:
The images in this document may differ from your computer depending on the configuration you ordered.
Recommended tools
The procedures in this document may require the following tools:
●
Phillips screwdriver #0
●
Phillips screwdriver #1
●
Plastic scribe
Screw list
NOTE:
When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and
then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is
restored when the component is replaced.
NOTE:
Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surfaces when
replacing a component.
NOTE:
Screw color may vary with the configuration ordered.
Table 1. Screw list
Component
Screw type
Quantity
Screw image
Solid-state drive
M2x3
1
Hard-drive and optical-drive
supporting bracket
#6-32
2
SD-card reader
M3x5
1
WLAN card
M2x3
1
Processor-fan and heat-sink
assembly
Captive
4
Voltage regulator heat-sink
Captive
4
Power-supply unit
#6-32
3
2
10
Removing and installing components