Dell OptiPlex 7000 Small Form Factor Service Manual - Page 65

Optional I/O modules (VGA/HDMI/DP/USB Type-C), Removing optional I/O module, Installing optional I/O

Get Dell OptiPlex 7000 Small Form Factor PDF manuals and user guides View all Dell OptiPlex 7000 Small Form Factor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

3. Follow the procedure in after working inside your computer. Optional I/O modules (VGA/HDMI/DP/USB Type-C) Removing optional I/O module Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the front bezel. 4. Remove the heat-sink and fan assembly. About this task The following images indicate the location of the optional I/O module and provides a visual representation of the removal procedure. NOTE: The removal procedure for the VGA/DP/HDMI/USB Type-C optional I/O modules are the same. Steps 1. Remove the two screws that secure the I/O module to the chassis. 2. Disconnect the I/O-module cable from the connector on the system board. 3. Remove the I/O module from the computer. Installing optional I/O module Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. Removing and installing components 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
3.
Follow the procedure in
after working inside your computer
.
Optional I/O modules (VGA/HDMI/DP/USB Type-C)
Removing optional I/O module
Prerequisites
1.
Follow the procedure in
before working inside your computer
.
2.
Remove the
side cover
.
3.
Remove the
front bezel
.
4.
Remove the
heat-sink and fan assembly
.
About this task
The following images indicate the location of the optional I/O module and provides a visual representation of the removal
procedure.
NOTE:
The removal procedure for the VGA/DP/HDMI/USB Type-C optional I/O modules are the same.
Steps
1.
Remove the two screws that secure the I/O module to the chassis.
2.
Disconnect the I/O-module cable from the connector on the system board.
3.
Remove the I/O module from the computer.
Installing optional I/O module
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
Removing and installing components
65