Dell OptiPlex 7000 Small Form Factor Service Manual - Page 68

Speakers, Removing the speaker

Get Dell OptiPlex 7000 Small Form Factor PDF manuals and user guides View all Dell OptiPlex 7000 Small Form Factor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Steps 1. Insert the first two rubber grommets on the chassis fan. 2. Place the fan thought the chassis and push the rubber grommets downward until they are secured to the chassis. 3. Align the slots on the fan with the second set of holes on the chassis. 4. Route the rubber grommets through the slots on the fan and pull the rubber grommets until the fan snaps into position. 5. Connect the fan cable to the connector on the system board. NOTE: Ensure that the orientation of air flow is toward the inside of the chassis, and the PPID label on the fan is on top as seen on the image above. Next steps 1. Install the disk-drive cage. 2. Install the 3.5-inch hard-drive. 3. Install the 2.5-inch hard-drive. 4. Install the front bezel. 5. Install the side cover. 6. Follow the procedure in after working inside your computer. Speakers Removing the speaker Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. About this task The following images indicate the location of the speaker and provide a visual representation of the removal procedure. 68 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Steps
1.
Insert the first two rubber grommets on the chassis fan.
2.
Place the fan thought the chassis and push the rubber grommets downward until they are secured to the chassis.
3.
Align the slots on the fan with the second set of holes on the chassis.
4.
Route the rubber grommets through the slots on the fan and pull the rubber grommets until the fan snaps into position.
5.
Connect the fan cable to the connector on the system board.
NOTE:
Ensure that the orientation of air flow is toward the inside of the chassis, and the PPID label on the fan is on top
as seen on the image above.
Next steps
1.
Install the
disk-drive cage
.
2.
Install the
3.5-inch hard-drive
.
3.
Install the
2.5-inch hard-drive
.
4.
Install the
front bezel
.
5.
Install the
side cover
.
6.
Follow the procedure in
after working inside your computer
.
Speakers
Removing the speaker
Prerequisites
1.
Follow the procedure in
before working inside your computer
.
2.
Remove the
side cover
.
About this task
The following images indicate the location of the speaker and provide a visual representation of the removal procedure.
68
Removing and installing components