Dell OptiPlex 7000 Small Form Factor Service Manual - Page 67

Installing the chassis fan

Get Dell OptiPlex 7000 Small Form Factor PDF manuals and user guides View all Dell OptiPlex 7000 Small Form Factor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

2. Remove the side cover. 3. Remove the front bezel. 4. Remove the 2.5-inch hard-drive. 5. Remove the 3.5-inch hard-drive. 6. Remove the disk-drive cage. About this task The following image indicates the location of the chassis fan and provide a visual representation of the removal procedure. Steps 1. Disconnect the chassis fan cable from the connector on the system board. 2. Locate the position of rubber grommets. 3. Gently pull the rubber grommets to release the fan from the chassis. 4. Remove the fan off the chassis. Installing the chassis fan Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the chassis fan and provide a visual representation of the installation procedure. Removing and installing components 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
2.
Remove the
side cover
.
3.
Remove the
front bezel
.
4.
Remove the
2.5-inch hard-drive
.
5.
Remove the
3.5-inch hard-drive
.
6.
Remove the
disk-drive cage
.
About this task
The following image indicates the location of the chassis fan and provide a visual representation of the removal procedure.
Steps
1.
Disconnect the chassis fan cable from the connector on the system board.
2.
Locate the position of rubber grommets.
3.
Gently pull the rubber grommets to release the fan from the chassis.
4.
Remove the fan off the chassis.
Installing the chassis fan
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the chassis fan and provide a visual representation of the installation procedure.
Removing and installing components
67