Dell OptiPlex 7000 Small Form Factor Service Manual - Page 57

Installing the voltage-regulator heat sink, Processor, Removing the processor

Get Dell OptiPlex 7000 Small Form Factor PDF manuals and user guides View all Dell OptiPlex 7000 Small Form Factor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Installing the voltage-regulator heat sink Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the voltage-regulator heat sink and provide a visual representation of the installation procedure. Steps 1. Place the voltage-regulator heat sink on the system board. 2. Align the captive screws on the voltage-regulator heat sink to the screw holes on the system board. 3. Tighten the four captive screws that secure the voltage-regulator heat stink to the system board. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer. Processor Removing the processor Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the 2.5-inch hard-drive. 4. Remove the 3.5-inch hard-drive. 5. Remove the heat-sink and fan assembly. 6. Remove the disk-drive cage. Removing and installing components 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Installing the voltage-regulator heat sink
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the voltage-regulator heat sink and provide a visual representation of the
installation procedure.
Steps
1.
Place the voltage-regulator heat sink on the system board.
2.
Align the captive screws on the voltage-regulator heat sink to the screw holes on the system board.
3.
Tighten the four captive screws that secure the voltage-regulator heat stink to the system board.
Next steps
1.
Install the
side cover
.
2.
Follow the procedure in
after working inside your computer
.
Processor
Removing the processor
Prerequisites
1.
Follow the procedure in
before working inside your computer
.
2.
Remove the
side cover
.
3.
Remove the
2.5-inch hard-drive
.
4.
Remove the
3.5-inch hard-drive
.
5.
Remove the
heat-sink and fan assembly
.
6.
Remove the
disk-drive cage
.
Removing and installing components
57