Dell OptiPlex 7000 Small Form Factor Service Manual - Page 59

Expansion card, Removing the graphics card

Get Dell OptiPlex 7000 Small Form Factor PDF manuals and user guides View all Dell OptiPlex 7000 Small Form Factor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Steps 1. Ensure that the release lever on the processor socket is fully extended in the open position. 2. Align the notches on the processor with the tabs on the processor socket and place the processor in the processor socket. NOTE: Ensure that the processor-cover notch is positioned underneath the alignment post. NOTE: The pin-1 corner of the processor has a triangle that aligns with the triangle on the pin-1 corner on the processor socket. When the processor is properly seated, all four corners are aligned at the same height. If one or more corners of the processor are higher than the others, the processor is not seated properly. 3. When the processor is fully seated in the socket, pivot the release-lever down and place it under the tab on the processor cover. Next steps 1. Install the disk-drive cage. 2. Install the heat-sink and fan assembly. 3. Install the 3.5-inch hard-drive. 4. Install the 2.5-inch hard-drive. 5. Install the front bezel. 6. Install the side cover. 7. Follow the procedure in after working inside your computer. Expansion card Removing the graphics card Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. About this task The following images indicate the location of the graphics card and provide a visual representation of the removal procedure. Removing and installing components 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Steps
1.
Ensure that the release lever on the processor socket is fully extended in the open position.
2.
Align the notches on the processor with the tabs on the processor socket and place the processor in the processor socket.
NOTE:
Ensure that the processor-cover notch is positioned underneath the alignment post.
NOTE:
The pin-1 corner of the processor has a triangle that aligns with the triangle on the pin-1 corner on the processor
socket. When the processor is properly seated, all four corners are aligned at the same height. If one or more corners of
the processor are higher than the others, the processor is not seated properly.
3.
When the processor is fully seated in the socket, pivot the release-lever down and place it under the tab on the processor
cover.
Next steps
1.
Install the
disk-drive cage
.
2.
Install the
heat-sink and fan assembly
.
3.
Install the
3.5-inch hard-drive
.
4.
Install the
2.5-inch hard-drive
.
5.
Install the
front bezel
.
6.
Install the
side cover
.
7.
Follow the procedure in
after working inside your computer
.
Expansion card
Removing the graphics card
Prerequisites
1.
Follow the procedure in
before working inside your computer
.
2.
Remove the
side cover
.
About this task
The following images indicate the location of the graphics card and provide a visual representation of the removal procedure.
Removing and installing components
59