Dell OptiPlex 7000 Small Form Factor Service Manual - Page 79

Optional I/O modules

Get Dell OptiPlex 7000 Small Form Factor PDF manuals and user guides View all Dell OptiPlex 7000 Small Form Factor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Steps 1. Align and lower the system board into the system until the stand-off points at the back of the system board align with those on the chassis. 2. Replace the four (#6-32) screws to secure the system board to the chassis. 3. Route and connect all the cables that you disconnected from the system board. 4. Place and align the front I/O-bracket with I/O slot on the chassis. 5. Replace the screw (#6-32) that secures the front I/O-bracket to the chassis. Next steps 1. Install the processor. 2. Install the heat-sink and fan assembly. 3. Install the WLAN card. 4. Install the solid-state drive. 5. Install the memory modules. 6. Install the expansion card. 7. Install the Optional I/O modules. 8. Install the disk-drive cage. 9. Install the 3.5-inch hard-drive. 10. Install the 2.5-inch hard-drive. 11. Install the front bezel. 12. Install the side cover. 13. Follow the procedure in after working inside your computer. Removing and installing components 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Steps
1.
Align and lower the system board into the system until the stand-off points at the back of the system board align with those
on the chassis.
2.
Replace the four (#6-32) screws to secure the system board to the chassis.
3.
Route and connect all the cables that you disconnected from the system board.
4.
Place and align the front I/O-bracket with I/O slot on the chassis.
5.
Replace the screw (#6-32) that secures the front I/O-bracket to the chassis.
Next steps
1.
Install the
processor
.
2.
Install the
heat-sink and fan assembly
.
3.
Install the
WLAN card
.
4.
Install the
solid-state drive
.
5.
Install the
memory modules
.
6.
Install the
expansion card
.
7.
Install the
Optional I/O modules
.
8.
Install the
disk-drive cage
.
9.
Install the
3.5-inch hard-drive
.
10.
Install the
2.5-inch hard-drive
.
11.
Install the
front bezel
.
12.
Install the
side cover
.
13.
Follow the procedure in
after working inside your computer
.
Removing and installing components
79