Dell OptiPlex 7000 Small Form Factor Service Manual - Page 52

Memory, Removing the memory

Get Dell OptiPlex 7000 Small Form Factor PDF manuals and user guides View all Dell OptiPlex 7000 Small Form Factor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

4. Install the nut and washer to secure the antenna-modules to the chassis. Next steps 1. Install the disk-drive cage. 2. Install the WLAN card. 3. Install the 3.5-inch hard-drive. 4. Install the 2.5-inch hard-drive. 5. Install the front bezel. 6. Install the side cover. 7. Follow the procedure in after working inside your computer. Memory Removing the memory Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the 2.5-inch hard-drive. 4. Remove the 3.5-inch hard-drive. 5. Remove the disk-drive cage. About this task The following images indicate the location of the memory modules and provide a visual representation of the removal procedure. Steps 1. Carefully spread apart the securing-clips on each end of the memory-module slot. 2. Grasp the memory module near the securing clip, and then gently ease the memory module out of the memory-module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges. Do not touch the components on the memory module NOTE: Repeat step 1 to step 2 to remove any other memory modules installed in your computer. 52 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
4.
Install the nut and washer to secure the antenna-modules to the chassis.
Next steps
1.
Install the
disk-drive cage
.
2.
Install the
WLAN card
.
3.
Install the
3.5-inch hard-drive
.
4.
Install the
2.5-inch hard-drive
.
5.
Install the
front bezel
.
6.
Install the
side cover
.
7.
Follow the procedure in
after working inside your computer
.
Memory
Removing the memory
Prerequisites
1.
Follow the procedure in
before working inside your computer
.
2.
Remove the
side cover
.
3.
Remove the
2.5-inch hard-drive
.
4.
Remove the
3.5-inch hard-drive
.
5.
Remove the
disk-drive cage
.
About this task
The following images indicate the location of the memory modules and provide a visual representation of the removal procedure.
Steps
1.
Carefully spread apart the securing-clips on each end of the memory-module slot.
2.
Grasp the memory module near the securing clip, and then gently ease the memory module out of the memory-module slot.
CAUTION:
To prevent damage to the memory module, hold the memory module by the edges. Do not touch
the components on the memory module
NOTE:
Repeat step 1 to step 2 to remove any other memory modules installed in your computer.
52
Removing and installing components