Dell PowerEdge R510 Hardware Owner's Manual - Page 129

Integrated Storage Controller Card, Removing the Storage Controller Card

Get Dell PowerEdge R510 PDF manuals and user guides View all Dell PowerEdge R510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 129 highlights

4 Reinstall the storage controller card. See "Installing the Storage Controller Card" on page 131. 5 Reconnect all cables. 6 Close the system. See "Closing the System" on page 89. 7 Reconnect the system and peripherals to their power sources. Integrated Storage Controller Card NOTE: This section applies to systems with hot-swappable hard drives. Your system includes a dedicated expansion-card slot on the riser for an integrated SAS or RAID controller card that provides the integrated storage subsystem for your system's hard drives. The controller supports SAS and SATA hard drives and also enables you to set up the hard drives in RAID configurations as supported by the version of the storage controller included with your system. Removing the Storage Controller Card CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 2 Open the system. See "Opening the System" on page 87. 3 If installed, remove the expansion card. See "Removing an Expansion Card" on page 126. 4 Disconnect the SAS cables connected to the card. 5 Disconnect the cable connecting the card to the expansion-card riser. 6 For a battery-cached RAID controller, disconnect the cable connecting the card to the RAID battery. 7 Bend both the card-edge guides outward and pull the storage controller card out of the connector. Installing System Components 129

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
Installing System Components
129
4
Reinstall the storage controller card. See "Installing the Storage Controller
Card" on page 131.
5
Reconnect all cables.
6
Close the system. See "Closing the System" on page 89.
7
Reconnect the system and peripherals to their power sources.
Integrated Storage Controller Card
NOTE:
This section applies to systems with hot-swappable hard drives.
Your system includes a dedicated expansion-card slot on the riser for an
integrated SAS or RAID controller card that provides the integrated storage
subsystem for your system’s hard drives. The controller supports SAS and
SATA hard drives and also enables you to set up the hard drives in RAID
configurations as supported by the version of the storage controller included
with your system.
Removing the Storage Controller Card
CAUTION:
Many repairs may only be done by a certified service technician.
You should only perform troubleshooting and simple repairs as authorized in
your product documentation, or as directed by the online or telephone service
and support team. Damage due to servicing that is not authorized by Dell is not
covered by your warranty. Read and follow the safety instructions that came
with the product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
Open the system. See "Opening the System" on page 87.
3
If installed, remove the expansion card. See "Removing an Expansion
Card" on page 126.
4
Disconnect the SAS cables connected to the card.
5
Disconnect the cable connecting the card to the expansion-card riser.
6
For a battery-cached RAID controller, disconnect the cable connecting the
card to the RAID battery.
7
Bend both the card-edge guides outward and pull the storage controller
card out of the connector.