Dell PowerEdge R510 Hardware Owner's Manual - Page 147

Installing the RAID Battery, Control Panel Assembly-LED (Optional)

Get Dell PowerEdge R510 PDF manuals and user guides View all Dell PowerEdge R510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 147 highlights

Installing the RAID Battery 1 Insert the RAID battery into the battery carrier until it locks into place. See Figure 3-29. 2 Connect the cable to the battery. See Figure 6-1. 3 Close the system. See "Closing the System" on page 89. 4 Turn on the system and attached peripherals. Control Panel Assembly-LED (Optional) Removing the Control Panel Assembly (Four-Hard-Drive System) CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1 If installed, remove the front bezel. See "Removing the Front Bezel" on page 86. 2 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals. 3 Open the system. See "Opening the System" on page 87. 4 Press the metal tabs at the end of the control panel cable and disconnect the cable at back of the control panel board. See Figure 3-30. 5 Disconnect the USB cable at back of the control panel board. See Figure 3-30. CAUTION: Do not pull on the cable to unseat the connector. Doing so can damage the cable. 6 Remove the two screws that secure the control panel board to the system chassis and remove the board. Installing System Components 147

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
Installing System Components
147
Installing the RAID Battery
1
Insert the RAID battery into the battery carrier until it locks into place.
See Figure 3-29.
2
Connect the cable to the battery. See Figure 6-1.
3
Close the system. See "Closing the System" on page 89.
4
Turn on the system and attached peripherals.
Control Panel Assembly—LED (Optional)
Removing the Control Panel Assembly (Four–Hard-Drive System)
CAUTION:
Many repairs may only be done by a certified service technician.
You should only perform troubleshooting and simple repairs as authorized in
your product documentation, or as directed by the online or telephone service
and support team. Damage due to servicing that is not authorized by Dell is not
covered by your warranty. Read and follow the safety instructions that came
with the product.
1
If installed, remove the front bezel. See "Removing the Front Bezel" on
page 86.
2
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet and peripherals.
3
Open the system. See "Opening the System" on page 87.
4
Press the metal tabs at the end of the control panel cable and disconnect
the cable at back of the control panel board. See Figure 3-30.
5
Disconnect the USB cable at back of the control panel board.
See Figure 3-30.
CAUTION:
Do not pull on the cable to unseat the connector. Doing so can
damage the cable.
6
Remove the two screws that secure the control panel board to the system
chassis and remove the board.