Dell PowerEdge R510 Hardware Owner's Manual - Page 157

Remove all hard drives. See Removing a Hot-Swap Hard Drive

Get Dell PowerEdge R510 PDF manuals and user guides View all Dell PowerEdge R510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 157 highlights

4 Remove all hard drives. See "Removing a Hot-Swap Hard Drive" on page 92. 5 Disconnect the power cable from the end of the SAS backplane. 6 Disconnect the SAS data cables from the backplane. 7 Disconnect the optical-drive cable, USB cable, and the control-panel cable. CAUTION: Handle the cables gently to prevent damage. NOTE: In case of the twelve-hard-drive systems, connect the internal hard-drive cables. 8 While pressing the two blue latches toward each other, lift the backplane upward. See Figure 3-35. 9 When the backplane cannot slide upward any farther, pull the backplane toward the back of the system to remove it from the retention hooks. 10 Lift the board out of the system, being careful to avoid damaging components on the face of the board. 11 Place the SAS backplane face down on a work surface. Installing System Components 157

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
Installing System Components
157
4
Remove all hard drives. See "Removing a Hot-Swap Hard Drive" on
page 92.
5
Disconnect the power cable from the end of the SAS backplane.
6
Disconnect the SAS data cables from the backplane.
7
Disconnect the optical-drive cable, USB cable, and the control-panel
cable.
CAUTION:
Handle the cables gently to prevent damage.
NOTE:
In case of the twelve–hard-drive systems, connect the internal
hard-drive cables.
8
While pressing the two blue latches toward each other, lift the backplane
upward. See Figure 3-35.
9
When the backplane cannot slide upward any farther, pull the backplane
toward the back of the system to remove it from the retention hooks.
10
Lift the board out of the system, being careful to avoid damaging
components on the face of the board.
11
Place the SAS backplane face down on a work surface.