Dell PowerStore 5000X EMC PowerStore Installation and Service Guide - Page 40

Install an embedded module

Get Dell PowerStore 5000X PDF manuals and user guides View all Dell PowerStore 5000X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

2. Align the white pegs beneath the holes on the 4-port card. CAUTION: Do not force the 4-port card into place. If the 4-port card does not smoothly seat, re-align the pegs and try again. Figure 35. Seating the 4-port card 3. Gently push down on the upper-left circle on the 4-port card. 4. Push up on the blue tabs until they lock into place. Figure 36. Locking the 4-port card into position 5. Replace the air dam and tighten the four captive screws. 6. Install the SFPs into the embedded module. Install an embedded module Steps 1. Align the embedded module with the empty slot and carefully push it into the slot. As the embedded module is installed, the release lever rotates inward. 40 Base enclosure service procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
2.
Align the white pegs beneath the holes on the 4-port card.
CAUTION:
Do not force the 4-port card into place. If the 4-port card does not smoothly seat, re-align the pegs and
try again.
Figure 35. Seating the 4-port card
3.
Gently push down on the upper-left circle on the 4-port card.
4.
Push up on the blue tabs until they lock into place.
Figure 36. Locking the 4-port card into position
5.
Replace the air dam and tighten the four captive screws.
6.
Install the SFPs into the embedded module.
Install an embedded module
Steps
1.
Align the embedded module with the empty slot and carefully push it into the slot.
As the embedded module is installed, the release lever rotates inward.
40
Base enclosure service procedures