Dell PowerStore 5000X EMC PowerStore Installation and Service Guide - Page 91

Removing a drive filler module, Installing a drive

Get Dell PowerStore 5000X PDF manuals and user guides View all Dell PowerStore 5000X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Removing a drive filler module Steps 1. Insert your finger into the cutout on the bottom of the drive filler module (2). 2. With your thumb push in the latch on the top of the drive filler module, and pull the module out of the slot (2). 1 2 CL5219 Figure 118. Removing a drive filler module Installing a drive About this task NOTE: If you are installing multiple drives in a system that is powered up, wait at least 10 seconds before sliding the next drive into position. Steps 1. Align the drive with the guides in the slot. 2. With the latch fully opened, gently push the drive into the slot. The latch begins to rotate downward when it meets the enclosure. 3. Push the orange button until the drive is fully seated in the slot. 4. Push the latch down until it locks into place. Expansion enclosure service procedures 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Removing a drive filler module
Steps
1.
Insert your finger into the cutout on the bottom of the drive filler module (2).
2.
With your thumb push in the latch on the top of the drive filler module, and pull the module out of the slot (2).
CL5219
1
2
Figure 118. Removing a drive filler module
Installing a drive
About this task
NOTE:
If you are installing multiple drives in a system that is powered up, wait at least 10 seconds before sliding the
next drive into position.
Steps
1.
Align the drive with the guides in the slot.
2.
With the latch fully opened, gently push the drive into the slot.
The latch begins to rotate downward when it meets the enclosure.
3.
Push the orange button until the drive is fully seated in the slot.
4.
Push the latch down until it locks into place.
Expansion enclosure service procedures
91