Dell PowerStore 5000X EMC PowerStore Installation and Service Guide - Page 54

Removing the power cable, Disengaging the locking mechanism

Get Dell PowerStore 5000X PDF manuals and user guides View all Dell PowerStore 5000X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Figure 55. Removing the power cable 2. Disconnect the network and all other cables from the back of the I/O modules and network ports on the node. NOTE: Do not remove any cables from the other node. 3. Pull the orange release trigger while gently pushing in on the node. The hook disengages from the locking mechanism, and the release tab slides out. NOTE: The node comes completely out of the chassis. Be prepared to support the node to avoid dropping it. Figure 56. Disengaging the locking mechanism 4. Use the release handle to pull the node outward enough to grasp the sides with both hands. Then, with both hands supporting the node, pull the node fully out of the enclosure. Figure 57. Removing the node 54 Base enclosure service procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Figure 55. Removing the power cable
2.
Disconnect the network and all other cables from the back of the I/O modules and network ports on the node.
NOTE:
Do not remove any cables from the other node.
3.
Pull the orange release trigger while gently pushing in on the node.
The hook disengages from the locking mechanism, and the release tab slides out.
NOTE:
The node comes completely out of the chassis. Be prepared to support the node to avoid dropping it.
Figure 56. Disengaging the locking mechanism
4.
Use the release handle to pull the node outward enough to grasp the sides with both hands. Then, with both hands supporting the
node, pull the node fully out of the enclosure.
Figure 57. Removing the node
54
Base enclosure service procedures