Dell PowerStore 5000X EMC PowerStore Installation and Service Guide - Page 97

LCC fault LED, Disconnecting an LCC cable

Get Dell PowerStore 5000X PDF manuals and user guides View all Dell PowerStore 5000X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

# # Figure 125. LCC fault LED CL5982 About this task CAUTION: The DAE must have at least one LCC installed while the enclosure is powered up; do not remove both LCCs while AC power is on. Steps 1. Attach an ESD wristband to your wrist and the enclosure. 2. Remove each cable connected to the LCC by gently pulling the connector latches to release the cable from the connector. Note where the cables connect to the LCC because you will reconnect them later. CL5983 Figure 126. Disconnecting an LCC cable 3. Remove the LCC: NOTE: The LCC comes completely out of the DAE chassis. In addition to holding the latches, be prepared to support the LCC to avoid dropping it. a. Locate the orange handle buttons on the LCC handles. Expansion enclosure service procedures 97

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
#
#
CL5982
Figure 125. LCC fault LED
About this task
CAUTION:
The DAE must have at least one LCC installed while the enclosure is powered up; do not remove both LCCs
while AC power is on.
Steps
1.
Attach an ESD wristband to your wrist and the enclosure.
2.
Remove each cable connected to the LCC by gently pulling the connector latches to release the cable from the connector.
Note where the cables connect to the LCC because you will reconnect them later.
CL5983
Figure 126. Disconnecting an LCC cable
3.
Remove the LCC:
NOTE:
The LCC comes completely out of the DAE chassis. In addition to holding the latches, be prepared to support
the LCC to avoid dropping it.
a.
Locate the orange handle buttons on the LCC handles.
Expansion enclosure service procedures
97