HP 450c HP DesignJet 430, 450C, and 455CA Printer - User's Guide - Page 60
the illustration below.
 |
View all HP 450c manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 60 highlights
Working with media Loading roll media 5 Remove the new roll from its wrapping, place it on the spindle, so that, as the media winds up from behind the roll, the media stop still on the spindle is on the right. Push the right media stop so that it is flush against the end of the roll (2 in the illustration below). Then insert the left media stop on the left end of the spindle. 2 3 1 6 Put the loaded spindle back in the printer, pushing first the right side into place and then the left. WARNING Make sure that each end of the spindle slots firmly into place with an audible "click". It is important to make sure that the spindle is firmly in place, otherwise it could fall off the printer. 2-18
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55 -
56 -
57 -
58 -
59 -
60 -
61 -
62 -
63 -
64 -
65 -
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
 |
 |
2–18
5
Remove the
new roll
from its wrapping, place it on the spindle, so that, as the
media winds up from behind the roll, the media stop still on the spindle is on the
right.
Push the right media stop so that it is flush against the end of the roll (2 in
the illustration below).
Then insert the left media stop on the left end of the
spindle.
3
1
2
6
Put the loaded spindle back in the printer, pushing first the right side into place and
then the left.
Make sure that each end of the spindle slots firmly into place with an audible
“click”.
It is important to make sure that the spindle is firmly in place, otherwise it
could fall off the printer.
Working with media
Loading roll media
WARNING