HP A4500A Hardware Manual - rp24xx, Customer Viewable - Page 131

System Console Configuration, C1099A VT-100 Mode Configuration. - emulator

Get HP A4500A - VMEbus Single Board Computer 744 Motherboard PDF manuals and user guides View all HP A4500A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

System Console Configuration System Console Configuration The following describes the steps required to configure the HP C1099A or 700/96 terminal for VT-100 mode for operation with an rp24xx server. C1099A VT-100 Mode Configuration. The following procedure outlines the steps to configure the C1099A terminal for VT-100 operation. To access the Setup menu in HPTerm emulation: 1. Press the F10 key to display the terminal local function labels, then Press F8 (config keys). You are now in the Quick (F1) menu. 2. Select the VT100 emulation by using the space bar to navigate through the available options. 3. Press the ESC key to save selected setup parameters and to exit the Setup menu. 4. Press the Y key when the blinking prompt Save all? (Y/N) appears in the upper right corner of the menu to save the settings in non-volatile memory. NOTE If you enter N when the Save all? (Y/N) prompt appears, the changes will take effect, but will be lost if the terminal is reset or powered off. HP700 VT-100 Mode Configuration The following procedure outlines the steps to configure the HP700 series terminal for VT-100 operation. NOTE You may use either the arrow keys or the tab key to move between the setting options on the screen. Be sure to save any configuration changes you make before proceeding to a new menu. 1. Press [User System] key. 2. Press [config keys] function key. [f8] 3. Press [terminal config] function key. [f5] 4. Move to Terminal ID and enter "vt100". 5. Move to TermMode and, using the [Prev] and [Next] keys, select "EM100". 6. Save the configuration. [f1] 7. Press the [config keys] function key. [f8] 8. Press the [ansi config] function key. [f6] Chapter 139

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
Chapter
System Console Configuration
139
System Console Configuration
The following describes the steps required to configure the HP C1099A or 700/96 terminal for VT-100 mode
for operation with an rp24xx server.
C1099A VT-100 Mode Configuration.
The following procedure outlines the steps to configure the C1099A terminal for VT-100 operation.
To access the Setup menu in HPTerm emulation:
1. Press the
F10
key to display the terminal local function labels, then Press
F8
(
config keys
).
You are now in the
Quick
(
F1
) menu.
2. Select the VT100 emulation by using the space bar to navigate through the available options.
3. Press the
ESC
key to save selected setup parameters and to exit the
Setup
menu.
4. Press the
Y
key when the blinking prompt
Save all? (Y/N)
appears in the upper right corner of the menu to save the settings in non-volatile memory.
NOTE
If you enter
N
when the
Save all? (Y/N)
prompt appears, the changes will take effect, but will be lost if the terminal is reset or
powered off.
HP700 VT-100 Mode Configuration
The following procedure outlines the steps to configure the HP700 series terminal for VT-100 operation.
NOTE
You may use either the arrow keys or the tab key to move between the setting options on the
screen.
Be sure to save any configuration changes you make before proceeding to a new menu.
1. Press
[User System]
key.
2. Press
[config keys]
function key.
[f8]
3. Press
[terminal config]
function key.
[f5]
4. Move to
Terminal ID
and enter “vt100”.
5. Move to
TermMode
and, using the
[Prev]
and
[Next]
keys, select “EM100”.
6. Save the configuration.
[f1]
7. Press the
[config keys]
function key.
[f8]
8. Press the
[ansi config]
function key.
[f6]