HP A4500A Hardware Manual - rp24xx, Customer Viewable - Page 163

Server Cover Replacement, Step 1.

Get HP A4500A - VMEbus Single Board Computer 744 Motherboard PDF manuals and user guides View all HP A4500A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 163 highlights

Server Cover Replacement Server Cover Replacement The cover that protects rp24xx server components must be raised in front and positioned on top of the side chassis panels then lowered and slid into the back chassis panel. The cover is secured by two thumbscrews attached to the front chassis panel. To replace the cover, perform the following procedures: Step 1. Tilt the cover front up slightly and position it on top of the chassis side panels approximately 2.5 MM (1 in.) from the rear of the server chassis. Step 2. Lower and slide the cover back over the notches on each side of the front of the server and seat it against the rear chassis panel. Step 3. Fasten the two captive knurled thumbscrews located near the bottom edge of the front of the server cover. CAUTION The server weighs approximately 23 kg (50 lbs). Take necessary precautions to prevent muscle strain when lifting and carrying the server. The following graphic shows the server cover suspended over the server. Chapter 235

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
Chapter
Server Cover Replacement
235
Server Cover Replacement
The cover that protects rp24xx server components must be raised in front and positioned on top of the side
chassis panels then lowered and slid into the back chassis panel. The cover is secured by two thumbscrews
attached to the front chassis panel.
To replace the cover, perform the following procedures:
Step 1.
Tilt the cover front up slightly and position it on top of the chassis side panels approximately 2.5
MM (1 in.) from the rear of the server chassis.
Step 2.
Lower and slide the cover back over the notches on each side of the front of the server and seat it
against the rear chassis panel.
Step 3.
Fasten the two captive knurled thumbscrews located near the bottom edge of the front of the server
cover.
CAUTION
The server weighs approximately 23 kg (50 lbs). Take necessary precautions to prevent muscle
strain when lifting and carrying the server.
The following graphic shows the server cover suspended over the server.