HP A4500A Hardware Manual - rp24xx, Customer Viewable - Page 157

Front Bezel Removal, WARNING, CAUTION

Get HP A4500A - VMEbus Single Board Computer 744 Motherboard PDF manuals and user guides View all HP A4500A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 157 highlights

Front Bezel Removal Front Bezel Removal The rp24xx server does not have to be turned off to remove the bezel. WARNING Do not attempt to lift or carry the server by the bezel. The bezel is made of plastic and is attached to the server chassis by two bezel retainers and four ball-posts. It will only support the weight of the server chassis in an emergency. Failure to heed this warning may result in personal injury and/or permanent damage to the server. Removing the bezel provides access to the following: • HotPlug Disk Drive access door. • Two knurled thumbscrews that secure the server cover. To remove the bezel, grasp the bezel at the sides and pull straight out until it is free of the bezel retainers and ball-posts on the server. CAUTION Pull the bezel straight out. Do not twist or wiggle from side-to-side any more than necessary to keep from damaging the bezel sockets. The following illustration shows a server and bezel with the bezel retainers and ball posts in an exploded view. The following picture shows one server with the front bezel attached and one server without. Chapter 229

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
Chapter
Front Bezel Removal
229
Front Bezel Removal
The rp24xx server does not have to be turned off to remove the bezel.
WARNING
Do not attempt to lift or carry the server by the bezel. The bezel is made of plastic
and is attached to the server chassis by two bezel retainers and four ball-posts. It
will only support the weight of the server chassis in an emergency.
Failure to heed this warning may result in personal injury and/or permanent
damage to the server.
Removing the bezel provides access to the following:
•
HotPlug Disk Drive access door.
•
Two knurled thumbscrews that secure the server cover.
To remove the bezel, grasp the bezel at the sides and pull straight out until it is free of the bezel retainers and
ball-posts on the server.
CAUTION
Pull the bezel straight out. Do not twist or wiggle from side-to-side any more than necessary to
keep from damaging the bezel sockets.
The following illustration shows a server and bezel with the bezel retainers and ball posts in an exploded
view.
The following picture shows one server with the front bezel attached and one server without.