HP AM866A Brocade Troubleshooting and Diagnostics Guide v6.1.0 (53-1000853-01, - Page 118

Automatic trace dump transfers, Setting the facility level, Removing a syslogd host from the list

Get HP AM866A - StorageWorks 8/8 Base SAN Switch PDF manuals and user guides
UPC - 884420064602
View all HP AM866A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

12 Automatic trace dump transfers switch:admin> syslogdipadd 10.1.2.4 switch:admin> syslogdipadd 10.1.2.5 switch:admin> syslogdipadd 10.1.2.6 switch:admin> syslogdipshow syslog.IP.address.1080::8:800:200C:417A syslog.IP.address.1081::8:800:200C:417A syslog.IP.address.1082::8:800:200C:417A syslog.IP.address.4 10.1.2.4 syslog.IP.address.5 10.1.2.5 syslog.IP.address.6 10.1.2.6 Setting the facility level 1. Connect to the switch and log in as admin. 2. Enter the following command: switch:admin> syslogdfacility -l n n is a number from 0 through 7, indicating a UNIX local7 facility. The default is 7. It is necessary to set the facility level only if you specified a facility other than local7 in the host /etc/syslog.conf file. Removing a syslogd host from the list 1. Connect to the switch and log in as admin. 2. Enter the syslogdIpRemove command: switch:admin> syslogdipremove 10.1.2.1 3. Verify the IP address was deleted using the syslogdIpShow command. Automatic trace dump transfers You can set up a switch so that diagnostic information is transferred automatically to a remote server. If a problem occurs, you can then provide your customer support representative with the most detailed information possible. To ensure the best service, you should set up for automatic transfer as part of standard switch configuration, before a problem occurs. Setting up for automatic transfer of diagnostic files involves the following tasks: • Specifying a remote server to store the files. • Enabling the automatic transfer of trace dumps to the server. (Trace dumps overwrite each other by default; sending them to a server preserves information that would otherwise be lost.) • Setting up a periodic checking of the remote server so that you are alerted if the server becomes unavailable and you can correct the problem. After the setup is complete, you can run the supportSave -c command to save RASLog, TRACE, supportShow, core file, FFDC data and other diagnostic support information to the server without specifying server details. The following procedures describe the tasks for setting up automatic transfer. For details on the commands, see the Fabric OS Command Reference. 104 Fabric OS Troubleshooting and Diagnostics Guide 53-1000853-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
104
Fabric OS Troubleshooting and Diagnostics Guide
53-1000853-01
Automatic trace dump transfers
12
switch:admin>
syslogdipadd 10.1.2.4
switch:admin>
syslogdipadd 10.1.2.5
switch:admin>
syslogdipadd 10.1.2.6
switch:admin>
syslogdipshow
syslog.IP.address.
1080::8:800:200C:417A
syslog.IP.address.
1081::8:800:200C:417A
syslog.IP.address.
1082::8:800:200C:417A
syslog.IP.address.4 10.1.2.4
syslog.IP.address.5 10.1.2.5
syslog.IP.address.6 10.1.2.6
Setting the facility level
1.
Connect to the switch and log in as admin.
2.
Enter the following command:
switch:admin> syslogdfacility -l
n
n
is a number from 0 through 7, indicating a UNIX local7 facility. The default is 7.
It is necessary to set the facility level only if you specified a facility other than local7 in the host
/etc/syslog.conf
file.
Removing a syslogd host from the list
1.
Connect to the switch and log in as admin.
2.
Enter the
syslogdIpRemove
command:
switch:admin>
syslogdipremove 10.1.2.1
3.
Verify the IP address was deleted using the
syslogdIpShow
command.
Automatic trace dump transfers
You can set up a switch so that diagnostic information is transferred automatically to a remote
server. If a problem occurs, you can then provide your customer support representative with the
most detailed information possible. To ensure the best service, you should set up for automatic
transfer as part of standard switch configuration, before a problem occurs.
Setting up for automatic transfer of diagnostic files involves the following tasks:
•
Specifying a remote server to store the files.
•
Enabling the automatic transfer of trace dumps to the server. (Trace dumps overwrite each
other by default; sending them to a server preserves information that would otherwise be lost.)
•
Setting up a periodic checking of the remote server so that you are alerted if the server
becomes unavailable and you can correct the problem.
After the setup is complete, you can run the
supportSave -c
command to save RASLog, TRACE,
supportShow, core file, FFDC data and other diagnostic support information to the server without
specifying server details.
The following procedures describe the tasks for setting up automatic transfer. For details on the
commands, see the
Fabric OS Command Reference
.