HP LaserJet 3200 HP LaserJet 3200m All-in-One Product - (English for Australia - Page 4

For direct connect installations, or network installations, For standalone installations

Get HP LaserJet 3200 - All-in-One Printer PDF manuals and user guides View all HP LaserJet 3200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

For direct connect installations or network installations: 8 Did the test page print (page 37 for direct, or page 41 for network)? o Yes. You have finished installing the software and setting the required settings. Continue to "Completing software installation" (on page 37 for direct connect installations, or on page 41 for network installations). o No. Do the following: • See chapter 3, "Installation troubleshooting," on page 53 to check for solutions to messages and common installation issues. • If the troubleshooting section does not resolve the issue, see "HP Customer Care" on page 58. 9 Did the document print (page 42)? o Yes. The new equipment is working correctly with your computer. • If you completed a direct connect installation, and want to allow other computers on your network print to the product, see "Sharing the product (for printing only)" on page 43. (If you do not want to share the product, you have completed installation. Continue to chapter 4, "Now that installation is complete . . .," on page 57.) • If you completed a network installation, Continue to chapter 4, "Now that installation is complete . . .," on page 57. o No. Do the following: • See chapter 3, "Installation troubleshooting," on page 53 to check for solutions to messages and common installation issues. • If the troubleshooting section does not resolve the issue, see "HP Customer Care" on page 58. For standalone installations: 10 After you set the time and date, does the control panel read READY, followed by the date and time you set (page 45)? o Yes. Continue to "To set the fax header" on page 46. o No. Do the following: • If the control panel display does not read READY, or does not show the correct time and date, complete all of the steps under "To set the time and date" again. • If the control panel display contains information about an error, see chapter 3, "Installation troubleshooting," on page 53. When the control panel reads READY, followed by the correct time and date, continue to "To set the fax header" on page 46. 11 Does the control panel display show the answer mode setting that you chose (page 48)? o Yes. If you have ring pattern service, continue to "Enabling answer ring patterns" on page 49; if you do not have ring pattern service, continue to "To print a configuration report" on page 51. o No. Try again to set the answer mode. 12 Do the settings you entered appear correctly? o Yes. You have completed the required settings. Continue to chapter 4, "Now that installation is complete . . ." o No. See "HP Customer Care" on page 58.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
For direct connect installations
or network installations:
8
Did the test page print (page 37 for
direct, or page 41 for network)?
o
Yes.
You have finished installing the
software and setting the required
settings. Continue to "Completing
software installation" (on page 37 for
direct connect installations, or on
page 41 for network installations).
o
No.
Do the following:
•
See chapter 3, “Installation
troubleshooting,” on page 53 to
check for solutions to messages
and common installation issues.
•
If the troubleshooting section does
not resolve the issue, see “HP
Customer Care” on page 58.
9
Did the document print (page 42)?
o
Yes.
The new equipment is working
correctly with your computer.
•
If you completed a direct connect
installation, and want to allow
other computers on your network
print to the product, see “Sharing
the product (for printing only)” on
page 43. (If you do not want to
share the product, you have
completed installation. Continue to
chapter 4, “Now that installation is
complete . . .,” on page 57.)
•
If you completed a network
installation, Continue to chapter 4,
“Now that installation is complete .
. .,” on page 57.
o
No.
Do the following:
•
See chapter 3, “Installation
troubleshooting,” on page 53 to
check for solutions to messages
and common installation issues.
•
If the troubleshooting section does
not resolve the issue, see “HP
Customer Care” on page 58.
For standalone installations:
10
After you set the time and date,
does the control panel read
READY
,
followed by the date and time you
set (page 45)?
o
Yes.
Continue to “To set the fax
header” on page 46.
o
No.
Do the following:
•
If the control panel display does
not read
READY
, or does not show
the correct time and date,
complete all of the steps under "To
set the time and date" again.
•
If the control panel display
contains information about an
error, see chapter 3, “Installation
troubleshooting,” on page 53.
When the control panel reads
READY
,
followed by the correct time and date,
continue to “To set the fax header” on
page 46.
11
Does the control panel display
show the answer mode setting that
you chose (page 48)?
o
Yes.
If you have ring pattern service,
continue to “Enabling answer ring
patterns” on page 49; if you do not
have ring pattern service, continue to
“To print a configuration report” on
page 51.
o
No.
Try again to set the answer
mode.
12
Do the settings you entered appear
correctly?
o
Yes.
You have completed the
required settings. Continue to
chapter 4, "Now that installation is
complete . . ."
o
No.
See “HP Customer Care” on
page 58.