Home » HP Manuals » Storage Devices » HP StorageWorks 16-EL » Manual Viewer

HP StorageWorks 16-EL SAN Switch 2/16 version 3.1.x - Installation Guide - Page 63

Important Information on Setting the Core PID Format, How to Check the Current Core PID Format

View all HP StorageWorks 16-EL manuals

Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Installing the SAN Switch 2/16 Important Information on Setting the Core PID Format The switch you have purchased may require a change to the configuration setting known as the Core PID format. A Core PID format is one of two addressing mechanisms used in Fibre Channel. The Core PID format is analogous to specifying the physical switch and port a device is attached to in data networks. It is not analogous to an IP address. PID formats are assigned by a Fibre Channel switch when a device logs into the fabric. An example Core PID might look like this: 011F00 In new installations, where both edge and the Core Switch 2/64 reside, you must verify that the edge switch (for example, SAN Switch 2/16) Core PID format matches the Core switch's PID format (always 1), before connecting to the SAN. If a switch is introduced to an existing SAN with a Core PID format setting that differs from the Core PID format setting in the SAN, the switch will segment. Note: If you are in the process of creating a new SAN, set the PID format to 1, if possible. How to Check the Current Core PID Format To determine a switch's current Core PID format, connect directly to a switch in your SAN and complete the following steps via a telnet session, or the Serial cable supplied with the switch. 1. Type configShow and press Enter. 2. About 15 lines down (press Enter to display more information on the page), locate the following line: fabric.ops.mode.pidFormat: [1 or 0] Note: In the above example, the Core PID format is 1 or 0, depending on the number displayed in the brackets. SAN Switch 2/16 Version 3.1.x Installation Guide 63

Section	Page
Contents	3
About this Guide	9
Overview	10
Intended Audience	10
Related Documentation	10
Conventions	11
Document Conventions	11
Table 1: Document Conventions	11
Text Symbols	11
Equipment Symbols	12
Rack Stability	14
Getting Help	15
HP Technical Support	15
HP Storage Website	15
HP Authorized Reseller	16
Overview	17
SAN Switch 2/16 Features	18
Firmware	18
Hardware	19
SFP Media Side	20
Figure 1: SFP media side	20
Optical Ports	20
ISL Trunking	21
SFPs	21
Power Supply Side	21
Figure 2: Power supply side	21
Field-Replaceable Units	21
Optional Hardware Kits	22
Table 2: SAN Switch 2/16 Orderable Hardware	22
Installing the SAN Switch 2/16	23
Unpack and Verify Carton Contents	24
Figure 3: Carton contents	25
Table 3: Shipping Carton Contents	26
Installation Guidelines	27
Selecting an Operating Location	27
Cooling Requirements	28
Power Requirements	28
Electrostatic Discharge Precautions	29
Installing the SAN Switch as a Stand-alone Unit	30
Installing the SAN Switch 2/16 in an HP 9000 Series or Comparable EIA Rack	31
Installing the Slide Rail Assemblies to the Switch	31
Separating the Inner Slide Rail Assembly from the Outer Slide Rail Assembly	31
Attaching the Inner Slide Rails to the Switch	32
Figure 4: Securing the inner slide rails to the switch	33
Attaching the Rear or Front Rack Mount Brackets	33
For Rear Rack Access	34
Figure 5: Attaching the rear rack mount brackets	34
For Front Rack Access	35
Attaching the Outer Slide Rails	35
Figure 6: Attaching the outer slide rails to the HP 9000 Series rack	37
Sliding the Switch into an HP 9000 Series or EIA Rack	38
Figure 7: Sliding the switch into an HP 9000 Series rack	39
Securing the Rack Mount Brackets	39
Installing the Switch in the Optional HP System/e Rack	40
Items Required for the HP System/e Rack	40
Figure 8: Installing the mounting brackets	41
Figure 9: Installing the tinnerman clips	42
Figure 10: Installing the rubber washers	43
Figure 11: Assembling the outer rails (HP rack)	44
Figure 12: Assembling the inner rails	44
Figure 13: Installing switch into the HP rack	45
Installing the Switch Using the HP StorageWorks SAN Switch Universal Rack Mount Kit	46
Figure 14: Installing the rear mounting brackets (HP 9000 Series or comparable EIA rack)	48
Figure 15: Installing the rear mounting brackets (HP System/e rack-left rear upright)	49
Figure 16: Installing the outer rails (HP 9000 Series or comparable EIA rack)	50
Figure 17: Assembling the outer rails (HP 9000 Series or comparable EIA rack)	51
Figure 18: Assembling the outer rails (HP System/e rack)	52
Figure 19: Assembling the inner rails	53
Figure 20: Installing the switch into a rack (HP 9000 Series or comparable EIA rack)	54
Figure 21: Installing the switch into a rack (HP System/e rack)	55
Connecting AC Power	56
Figure 22: Connecting the power cords	56
Power-On Self Test	57
Checking POST Results	58
Configuring Network Addressing	58
Requirements	58
Setting Network Addresses via a Serial Connection	59
Figure 23: Connecting the Serial cable	59
Connecting the Switch to the LAN	62
Figure 24: Connecting the Ethernet cable	62
Important Information on Setting the Core PID Format	63
How to Check the Current Core PID Format	63
How to Change the Core PID Format	64
Modifying Domain IDs	65
Specifying Custom Status Policies	66
Connecting the Switch to the Fabric	66
Figure 25: Inserting a cable into an SFP	67
Verifying Operation	67
Installing Multiple Switches into an Existing SAN	68
Next Steps	69
Setting QuickLoop Mode on Ports	69
Setting Up Speed Negotiation	69
Cascading Switches	70
Managing the SAN Switch 2/16	71
Interpreting LED Activity	72
Front Panel LEDs	72
Table 4: Front Panel LED Patterns During Normal Operation	73
Rear Panel LEDs	76
Table 5: Rear Panel LED Patterns During Normal Operation	76
Management Overview	78
Optional Management Features	78
Displaying the Optional Feature Licenses	78
Enabling Licensed Features	79
Running Basic Switch Operations Using Telnet	79
Logging into the Switch	79
Changing the Admin Password and User ID	80
Configuring the IP and Fibre Channel Address	81
Displaying Devices within the Fabric	82
Checking the Firmware Version	82
Setting the Switch Date and Time	82
Displaying Switch Configuration Settings	83
Diagnostic Tests	84
Interpreting POST Results	84
Diagnostic Tests	84
Backing Up the Configuration and Upgrading Firmware	85
Backing Up System Configuration Settings	86
Restoring the System Configuration Settings	87
Upgrading or Restoring the Switch Firmware	88
Downloading Firmware from the HP Website	89
Regulatory Compliance Notices	91
FCC EMC Statement (USA)	91
EMC Statement (Canada)	92
EMC Statement (European Union)	92
Spécification ATI Classe A (France)	92
Germany Noise Declaration	92
VCCI EMC Statement (Japan)	92
Harmonics Conformance (Japan)	93
BSMI EMC Statement (Taiwan)	93
RRL EMC Statement (Korea)	93
Laser Safety	94
Battery Replacement Notice	95
Electrostatic Discharge	97
Grounding Methods	98
Technical Specifications	99
Dimensions	100
Table 6: Physical Specifications	100
Power Supply Specifications	101
Table 7: Power Supply Specifications	101
Environmental Requirements	102
Table 8: Environmental Requirements	102
Memory Specifications	103
Table 9: Cabling Pinouts if Pin 7 is Used	103
Glossary	105
Index	117
A	117
B	117
C	117
D	117
E	118
F	118
G	118
H	118
I	118
L	118
M	118
N	118
O	118
P	118
R	119
S	119
T	119
U	119
V	119
W	120