HP StorageWorks 2/32 SAN switch 2/32 version 4.0.2b release notes - Page 30

Operands, Example, See Also, Command Enhancements, supportShow Command

Get HP StorageWorks 2/32 - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Fabric OS Commands Operands This command has the following operands: ■ slot-Specify the slot number in a Core Switch. The slot number must be followed by a slash ( / ) and the port number. The Core Switch has a total of ten slots counted from 1 to 10. Slot number 5 and 6 are Control Processor cards, and slot 1 - 4 and 7 - 10 are switch cards. On each switch card, there are sixteen ports counted from the bottom 0 to 15. A particular port must be represented by both slot number (1 - 4 or 7 - 10) and port number (0 - 15). ■ port-Specify a port number (0 - 15). ■ mode-Specify a value of 1 to delay the FLOGI Accept for this port until route setup is complete. Specify a value of 0 to de-configure the delay of the FLOGI Accept for this port. Example To configure switch port 3 as a "delayed FLOGI" port: switch:admin> portcfgdelayflogi 1/3, 1 done. See Also portShow, switchShow, configure, portCfgLport, haFailover Command Enhancements supportShow Command The supportShow command with no additional parameters will now output information for all 64 ports within a single logical switch. The output from the following commands have been added to the output of the supportShow command: fabStateShow fabSwitchShow chassisShow fanShow historyShow 30 SAN switch 2/32 Version 4.0.2b Release Notes

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Fabric OS Commands
30
SAN switch 2/32 Version 4.0.2b Release Notes
Operands
This command has the following operands:
■
slot-Specify the slot number in a Core Switch. The slot number must be
followed by a slash ( / ) and the port number. The Core Switch has a total of
ten slots counted from 1 to 10. Slot number 5 and 6 are Control Processor
cards, and slot 1 - 4 and 7 - 10 are switch cards. On each switch card, there are
sixteen ports counted from the bottom 0 to 15. A particular port must be
represented by both slot number (1 - 4 or 7 - 10) and port number (0 - 15).
■
port-Specify a port number (0 - 15).
■
mode-Specify a value of 1 to delay the FLOGI Accept for this port until route
setup is complete. Specify a value of 0 to de-configure the delay of the FLOGI
Accept for this port.
Example
To configure switch port 3 as a “delayed FLOGI” port:
switch:admin> portcfgdelayflogi 1/3, 1
done.
See Also
portShow, switchShow, configure, portCfgLport, haFailover
Command Enhancements
supportShow
Command
The
supportShow
command with no additional parameters will now output
information for all 64 ports within a single logical switch. The output from the
following commands have been added to the output of the
supportShow
command:
fabStateShow
fabSwitchShow
chassisShow
fanShow
historyShow