HP StorageWorks 2/32 SAN switch 2/32 version 4.0.2b release notes - Page 50

Additional CLI commands, portcfglongdistance

Get HP StorageWorks 2/32 - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Additional CLI commands Virtual Channel parameters (yes, y, no, n): [no] Switch Operating Mode (yes, y, no, n): [no] Zoning Operation parameters (yes, y, no, n): [no] RSCN Transmission Mode (yes, y, no, n): [no] Arbitrated Loop parameters (yes, y, no, n): [no] System services (yes, y, no, n): [no] Portlog events enable (yes, y, no, n): [no] Committing configuration...done. switch:admin> switchenable Use cfgEnable [active_zoning_config] on the switch to update zoning to use the new PID format. This does not change the definition of zones in the fabric, but causes the lowest level tables in the zoning database to be updated with the new PID format setting. Example: switch:admin> cfgEnable myZoningCfg Finally, use the switchEnable command to re-enable the switch. Once this is done on every switch in the fabric, all switches in the fabric will operate with the new addressing mode. Note: For more information on upgrading to larger port count switches, refer to the HP SAN Design Guide and HP support services. Additional CLI commands portcfglongdistance Extended links in the same SAN are either 1 Gbps or 2 Gbps, but not both. If you have 1 Gbps extended links in the SAN you can not add a 2 Gbps Extended Link to the same SAN. 50 SAN switch 2/32 Version 4.0.2b Release Notes

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Additional CLI commands
50
SAN switch 2/32 Version 4.0.2b Release Notes
Virtual Channel parameters (yes, y, no, n): [no]
Switch Operating Mode (yes, y, no, n): [no]
Zoning Operation parameters (yes, y, no, n): [no]
RSCN Transmission Mode (yes, y, no, n): [no]
Arbitrated Loop parameters (yes, y, no, n): [no]
System services (yes, y, no, n): [no]
Portlog events enable (yes, y, no, n): [no]
Committing configuration...done.
switch:admin> switchenable
Use
cfgEnable
[
active_zoning_config
] on the switch to update zoning
to use the new PID format. This does not change the definition of zones in the
fabric, but causes the lowest level tables in the zoning database to be updated with
the new PID format setting.
Example:
switch:admin> cfgEnable myZoningCfg
Finally, use the
switchEnable
command to re-enable the switch.
Once this is done on every switch in the fabric, all switches in the fabric will
operate with the new addressing mode.
Note:
For more information on upgrading to larger port count switches, refer to the HP
SAN Design Guide and HP support services.
Additional CLI commands
portcfglongdistance
Extended links in the same SAN are either 1 Gbps or 2 Gbps, but not both. If you
have 1 Gbps extended links in the SAN you can not add a 2 Gbps Extended Link
to the same SAN.