HP StorageWorks 8/80 HP StorageWorks 8Gb SAN Switch hardware reference manual - Page 29

Installing the switch using the SAN Switch Rack Mount Kit, Place the switch on

Get HP StorageWorks 8/80 - SAN Switch PDF manuals and user guides View all HP StorageWorks 8/80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Installing the switch as a stand-alone device To install the switch as a stand-alone unit: 1. Unpack the switch, and verify that all items listed in "Shipping carton contents" on page 25 are present. 2. Locate the four rubber feet in the accessory box. 3. Apply the adhesive rubber feet to the switch. The rubber feet help prevent the switch from sliding off the supporting surface: a. Clean the indentations at each corner of the bottom of the switch, to ensure that they are free of dust or other debris that might lessen the adhesion of the feet. b. With the adhesive side against the chassis, place one rubber foot in each indentation, and press into place. 4. Place the switch on a flat, sturdy surface. 5. Apply power to the switch as described in "Powering the 8/8 or 8/24 SAN Switch on and off" on page 47 or "Powering the 8/40 or 8/80 SAN Switch on and off" on page 47. CAUTION: Do not connect the switch to the network until the IP address is set. See "Set the IP address" on page 42. 8Gb SAN Switch hardware reference manual 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Installing the switch as a stand-alone device
To install the switch as a stand-alone unit:
1.
Unpack the switch, and verify that all items listed in “
Shipping carton contents
” on page 25 are
present.
2.
Locate the four rubber feet in the accessory box.
3.
Apply the adhesive rubber feet to the switch. The rubber feet help prevent the switch from sliding
off the supporting surface:
a.
Clean the indentations at each corner of the bottom of the switch, to ensure that they are free of
dust or other debris that might lessen the adhesion of the feet.
b.
With the adhesive side against the chassis, place one rubber foot in each indentation, and
press into place.
4.
Place the switch on a
fl
at, sturdy surface.
5.
Apply power to the switch as
described in
“
Powering the 8/8 or 8/24 SAN Switch on and off
” on page 47 or
“
Powering the 8/40 or 8/80 SAN Switch on and off
” on page 47.
CAUTION:
Do not connect the switch to the network until the IP address is set. See “
Set the IP address
” on page 42.
8Gb SAN Switch hardware reference manual
29