HP Superdome SX2000 Installation Guide, Sixth Edition - HP Integrity Superdome - Page 29

Attaching the Side Skins and Blower Side Bezels, Attaching the Side Skins

Get HP Superdome SX2000 PDF manuals and user guides View all HP Superdome SX2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Figure 1-16 Installing the Blowers 7. Tighten the thumbscrews at the front of each blower. 8. If required, install housings on any other cabinets that were shipped with the system. Attaching the Side Skins and Blower Side Bezels Two cosmetic side panels affix to the left and right sides of the system. In addition, each system has bezels that cover the sides of the blowers. IMPORTANT: Be sure to attach the side skins at this point in the installation sequence, especially if the cabinet is to be positioned at the end of a row of cabinets or between cabinets. Attaching the Side Skins Each system has four side skins: two front-side skins and two rear-side skins. NOTE: Attach side skins to the left side of cabinet 0 and the right side of cabinet 1 (if applicable). To attach the side skins, follow these steps: 1. If not already done, remove the side skins from their boxes and protective coverings. 2. From the end of the brackets at the back of the cabinet, position the side skin with the lap joint (Rear) over the top bracket and under the bottom bracket, and gently slide it into position (Figure 1-17). Two skins are installed on each side of the cabinet: one has a lap joint (Rear) and one does not (Front). The side skins with the lap joint are marked Rear and the side skins without the lap joint are marked Front. Setting Up the System 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Figure 1-16 Installing the Blowers
7.
Tighten the thumbscrews at the front of each blower.
8.
If required, install housings on any other cabinets that were shipped with the system.
Attaching the Side Skins and Blower Side Bezels
Two cosmetic side panels affix to the left and right sides of the system. In addition, each system
has bezels that cover the sides of the blowers.
IMPORTANT:
Be sure to attach the side skins at this point in the installation sequence, especially
if the cabinet is to be positioned at the end of a row of cabinets or between cabinets.
Attaching the Side Skins
Each system has four side skins: two front-side skins and two rear-side skins.
NOTE:
Attach side skins to the left side of cabinet 0 and the right side of cabinet 1 (if applicable).
To attach the side skins, follow these steps:
1.
If not already done, remove the side skins from their boxes and protective coverings.
2.
From the end of the brackets at the back of the cabinet, position the side skin
with the lap
joint
(Rear) over the top bracket and under the bottom bracket, and gently slide it into position
(
Figure 1-17
).
Two skins are installed on each side of the cabinet: one has a lap joint (Rear) and one does
not (Front). The side skins with the lap joint are marked
Rear
and the side skins without the
lap joint are marked
Front.
Setting Up the System
29