HP Visualize J5000 hp Visualize J5000, J7000 workstations parts removal and re - Page 8

Replacement Part Kit Contents, Required Tools, Safely Powering Down the J Class Workstation

Get HP Visualize J5000 - Workstation PDF manuals and user guides View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Getting Started Replacement Part Kit Contents • Connect all equipment together, including the static-free mat, static strap, clips attached to the wrist strap, and peripheral units. • Keep uninstalled printed circuit boards in their protective antistatic bags. • Once you have removed printed circuit boards from their protective antistatic bags, handle the printed circuit boards by their edges only. Replacement Part Kit Contents Take a moment to verify that your kit contains the following contents: • Replacement Part • Part Number: A3024-80004, Electrostatic Discharge (ESD) Materials • Removal/Replacement Guide If you are missing any part or any documentation, please call your designated service representative. Required Tools You will need the following tools for removal/replacement procedures: • T-10 or T-15 Torx drivers • Light-duty flat blade screwdriver with a 150mm (6-inch) blade • Needle-nose pliers • ESD materials Safely Powering Down the J Class Workstation You must complete the following steps before performing any of the removal and replacement procedures: CAUTION Do not use the power supply interlock thumbscrew on the rear panel to power down the workstation. This power down method may hang the operating system in an unrecoverable state. 8 Chapter 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
8
Chapter 1
Getting Started
Replacement Part Kit Contents
•
Connect all equipment together, including the static-free mat, static strap, clips
attached to the wrist strap, and peripheral units.
•
Keep uninstalled printed circuit boards in their protective antistatic bags.
•
Once you have removed printed circuit boards from their protective antistatic bags,
handle the printed circuit boards by their edges only.
Replacement Part Kit Contents
Take a moment to verify that your kit contains the following contents:
•
Replacement Part
•
Part Number: A3024-80004, Electrostatic Discharge (ESD) Materials
•
Removal/Replacement Guide
If you are missing any part or any documentation, please call your designated service
representative.
Required Tools
You will need the following tools for removal/replacement procedures:
•
T-10 or T-15 Torx drivers
•
Light-duty flat blade screwdriver with a 150mm (6-inch) blade
•
Needle-nose pliers
•
ESD materials
Safely Powering Down the J Class Workstation
You
must
complete
the
following
steps
before
performing
any
of
the
removal
and
replacement procedures:
CAUTION
Do not use the power supply interlock thumbscrew on the rear panel to power
down the workstation. This power down method may hang the operating
system in an unrecoverable state.