IBM 8668 Hardware Maintenance Manual - Page 92

Installing the cover (rack)

Get IBM 8668 - Eserver xSeries 232 PDF manuals and user guides
UPC - 087944723158
View all IBM 8668 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

2. Press the top of the bezel toward the server until it clicks into place. To install the server door: 1. Set the door on the bottom hinge. 2. Press the flange downward while pressing the top of the door toward the server, until the flange connects with the top hinge. Then, release the flange. 3. Close and lock the server door. Attention: Be sure to maintain a clearance of at least 127 mm (5 inches) on the front and rear of the server to allow for air circulation. Installing the cover (rack) Note: The illustrations in this document might differ slightly from your hardware. Flange Top cover Flange Side latches To install the server top cover: 1. Align the top cover with the top of the server, approximately 25 mm (1 inch) from the front of the server; the flanges on the left and right sides of the cover should be on the outside of the server chassis. 2. Hold the cover against the server, and slide the cover toward the front of the server until the cover clicks into place. 84 Hardware Maintenance Manual: xSeries 232, Type 8668

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
2.
Press the top of the bezel toward the server until it clicks into place.
To install the server door:
1.
Set the door on the bottom hinge.
2.
Press the flange downward while pressing the top of the door toward the
server, until the flange connects with the top hinge. Then, release the flange.
3.
Close and lock the server door.
Attention:
Be sure to maintain a clearance of at least 127 mm (5 inches) on
the front and rear of the server to allow for air circulation.
Installing the cover (rack)
Note:
The illustrations in this document might differ slightly from your hardware.
Flange
Flange
Top cover
Side latches
To install the server top cover:
1.
Align the top cover with the top of the server, approximately 25 mm (1 inch)
from the front of the server; the flanges on the left and right sides of the cover
should be on the outside of the server chassis.
2.
Hold the cover against the server, and slide the cover toward the front of the
server until the cover clicks into place.
84
Hardware Maintenance Manual: xSeries 232, Type 8668