IBM 867431X Hardware Maintenance Manual - Page 71

Your server comes with riser cards installed in the two peripheral component

Get IBM 867431X - Eserver xSeries 330 PDF manuals and user guides View all IBM 867431X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Your server comes with riser cards installed in the two peripheral component interconnect (PCI) adapter slots on the system board. The following illustration shows the location of the 33 MHz PCI expansion slots on the system board. PCI slot 2 64 bit 33 MHz (J23) PCI slot 1 64 bit 33 MHz (J10) To install the Remote Supervisor Adapter, complete the following steps: 1. Review the safety precautions in "Safety information" on page 147. 2. Turn off the server and attached devices and disconnect all external cables and power cords. 3. To remove the cover, complete the following steps: a. Remove the server from the rack (if necessary). b. Remove the two screws from the back of the server. c. Pull out on the cover release lever at the back of the server to release the cover. d. Slide the cover back, then up and off the server. Attention: For proper cooling and airflow, replace the cover before turning on the server. Operating the server for extended periods of time (over 30 minutes) with the cover removed might damage server components. Installing options 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
Your server comes with riser cards installed in the two peripheral component
interconnect (PCI) adapter slots on the system board.
The following illustration shows the location of the 33 MHz PCI expansion slots on
the system board.
PCI slot 2
64 bit
33 MHz (J23)
PCI slot 1
64 bit
33 MHz (J10)
To install the Remote Supervisor Adapter, complete the following steps:
1.
Review the safety precautions in
“
Safety information
”
on page 147.
2.
Turn off the server and attached devices and disconnect all external cables and
power cords.
3.
To remove the cover, complete the following steps:
a.
Remove the server from the rack (if necessary).
b.
Remove the two screws from the back of the server.
c.
Pull out on the cover release lever at the back of the server to release the
cover.
d.
Slide the cover back, then up and off the server.
Attention:
For proper cooling and airflow, replace the cover before
turning on the server. Operating the server for extended periods of time
(over 30 minutes) with the cover removed might damage server
components.
Installing options
63