Icom IC-7600 Instruction Manual - Page 14
Main/sub Change Switch [change], Split Operation Indicator [split] - hf
View all Icom IC-7600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
1 PANEL DESCRIPTION ■ Front panel (continued) #0 #1 #2 #3 #4 #5 #6 #7 #8 #9 TIMER POWER HF/50MHz TRANSCEIVER TRANSMIT PHONES TUNER MONITOR BAL NR ELEC-KEY NB NR AF RF/SQL MIC MIC GAIN RF POWER BK-IN DELAY KEY SPEED TX RX SPLIT LOCK SPLIT 1.8 1 3.5 2 7 3 10 4 14 5 18 6 DUAL WATCH 21 7 24 8 28 9 CHANGE GENE 50 0 F-INP ENT MAIN /SUB M.SCOPE MP-W MW MP-R VFO/MEMO XFC TS TWIN-PBT PBT-CLR NOTCH APF/TPF NOTCH CW PITCH F-1 SSB F-2 F-3 F-4 F-5 F-6 AUTO TUNE CW RTTY/PSK AM / FM FILTER EXIT/SET REC PLAY VOICE MEMORY RIT ӠTX CLEAR RIT/ӠTX SPEECH LOCK $5 $4 $0 $1 $2 $3 #0 TRANSMIT INDICATOR [TX] Lights red while transmitting. #1 RECEIVE INDICATOR [RX] Lights green while receiving a signal and when the squelch is open. #2 L CD FUNCTION DISPLAY (p. 13) Shows the operating frequency, function switch menus, spectrum scope screen, memory list screen, set mode settings, etc. #3 SPLIT OPERATION INDICATOR [SPLIT] (p. 88) Lights during split frequency operation. #4 MAIN/SUB CHANGE SWITCH [CHANGE] ➥ Switches the frequency and selected memory channel between main and sub readouts when pushed. • Switches between transmit frequency and receive frequency when the split frequency function is ON. (p. 88) ➥ Equalizes the sub readout frequency to the main readout frequency when pushed and held for 1 sec. #5 L OCK INDICATOR [LOCK] (p. 82) Lights when the dial lock function is activated. #6 DUALWATCH SWITCH [DUALWATCH] (p. 79) ➥ Push to turn the dualwatch function ON and OFF. • " " appears when the dualwatch function is in use. ➥ Push and hold for 1 sec. to turn the dualwatch function ON and equalizes the sub readout fre- quency to the main readout. (Quick dualwatch function) • The quick dualwatch function can be turned OFF in others set mode. (p. 128) #7 SPLIT SWITCH [SPLIT] (p. 88) ➥ Push to turn the split function ON and OFF. • " " appears when the split function is in use. ➥ Push and hold for 1 sec. to activate the quick split function. • The split function ON and equalize the sub readout frequency to the main readout and sets the sub readout for frequency input in non-FM modes. (p. 89) • The offset frequency is shifted from the selected VFO frequency in FM mode. (p. 129) • The tone encoder function is turned ON in FM mode. • The quick split function can be turned OFF in others set mode. (p. 129) #8 KEYPAD ➥ Pushing a key selects the operating band. (p. 27) • [GEN •] selects the general coverage band. ➥ P ushing the same key 2 or 3 times calls up other stacked frequencies in the band. (p. 27) • Icom's triple band stacking register memorizes 3 frequencies in each band. ➥ A fter pushing [F-INP ENT], push a key on the keypad to enter a numeric frequency. After entering, push [F-INP ENT] to select the desired frequency directly (p. 28) • e .g. to enter 14.195 MHz; Push [F-INP ENT] [1] [4] [•] [1] [9] [5] [F-INP ENT]. ➥ A fter pushing [F-INP ENT], push a key on the keypad to enter a memory channel. After entering, push to select the desired memory channel directly. (p. 99)