Home » Icom Manuals » Two-Way Radios » Icom IC-7600 » Manual Viewer

Icom IC-7600 Instruction Manual - Page 90

■ Notch function, NOTCH], <MODE> CW/AM, AUTO TUNE]

Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

4 RECEIVE AND TRANSMIT ■ Notch function This transceiver has auto and manual notch functions. The auto notch function uses DSP to automatically attenuate beat tones, tuning signals, etc., even if they are moving. The manual notch can be set to attenuate a frequency via the [NOTCH] control. The auto notch can be used in SSB, AM and FM mode. The manual notch can be used in SSB, CW, RTTY, PSK and AM modes. ➥ P ush [NOTCH] to toggle the notch function between auto, manual and OFF in SSB and AM modes. • Either auto or manual notch function can be deactivated in others set mode. (p. 132) ➥ Push [NOTCH] to turn the manual notch function ON and OFF in CW, RTTY, PSK modes. ➥ Push [NOTCH] to turn the auto notch function ON and OFF in FM mode. • The indicator on this switch lights green when the auto or manual notch function is ON. • When the manual notch function is ON, push and hold [NOTCH] for 1 sec. to select the notch filter width for manual notch from wide, middle and narrow. • Set to attenuate a frequency for manual notch via the [NOTCH] control. • " " appears when auto notch is in use. • " " appears when manual notch is in use. While tuning the manual notch, noise may be heard. This comes from the DSP unit and does not indicate an equipment malfunction. • Auto notch indication NOTCH [NOTCH] control Appears • Manual notch indication Appears Auto notch OFF Auto notch ON Desired signal (AF) Desired signal (AF) ■ Auto tune function CW/AM The automatic tuning function tunes the displayed frequency automatically when an off-frequency signal is received within the range ±500 Hz (CW) or ±5 kHz (AM). This function is active while in CW or AM mode is selected. Unwanted tone frequency Particular frequency is attenuated ➥ Push [AUTO TUNE] to toggle the auto tune function ON or OFF. • " " blinks when auto tune function is acti- vated. • After 2 sec. has passed, the auto tune function stops tuning automatically even it's still off-frequency. Appears AUTO TUNE IMPORTANT! When receiving a weak signal, or receiving a signal with interference, the automatic tuning function may tune the receiver to an undesired signal. NOTE: The automatic tuning function does not active on the sub band. 83

Section	Page
Front cover	1
FOREWORD	2
IMPORTANT	2
EXPLICIT DEFINITIONS	2
SUPPLIED ACCESSORIES	2
FCC INFORMATION	2
PRECAUTIONS	3
TABLE OF CONTENTS	4
1 PANEL DESCRIPTION	8
■ Front panel	8
■ Rear panel	18
■ LCD display	20
■ Screen menu arrangement	22
2 INSTALLATION AND CONNECTIONS	23
■ Unpacking	23
■ Selecting a location	23
■ Grounding	23
■ Antenna connection	23
■ Required connections	24
◇ Front panel	24
◇ Rear panel	24
■ Advanced connections	25
◇ Front panel	25
◇ Rear panel— 1	25
◇ Rear panel— 2	26
■ USB connection	26
■ Power supply connections	27
■ External antenna tuner connection	27
■ Linear amplifier connections	28
◇ Connecting the IC-PW1/EURO	28
◇ Connecting a non-Icom linear amplifier	28
■ Transverter jack information	29
■ FSK and AFSK (SSTV) connections	29
◇ FSK operation— when connecting to [ACC 1]	29
◇ AFSK operation	29
◇ When connecting to the [USB] connector	29
■ Microphone connector information	30
■ Microphones	30
◇ HM-36	30
◇ SM-50 (Option)	30
■ Accessory connector information	31
3 BASIC OPERATION	32
■ Before first applying power	32
■ Applying power (CPU resetting)	32
■ Selecting VFO/memory mode	33
■ Main/Sub band selection	33
◇ Main/Sub band switching	33
◇ Main/Sub band equalization	33
■ Selecting an operating band	34
◇ Using the band stacking registers	34
■ Frequency setting	35
◇ Tuning with the main dial	35
◇ Direct frequency entry with the keypad	35
◇ About 5 MHz band operation (USA version only)	36
◇ Quick tuning step	36
◇ Selecting “kHz” step	36
◇ Selecting 1 Hz step	37
◇ Auto tuning step function	37
◇ 1⁄4 tuning step function	37
◇ Band edge warning beep	38
■ Operating mode selection	39
■ Squelch and receive (RF) sensitivity	40
■ Volume setting	41
■ Meter indication selection	41
◇ Multi-function digital meter	41
◇ Meter type selection	42
■ Voice synthesizer operation	42
■ Basic transmit operation	43
◇ Transmitting	43
◇ Microphone gain adjustment	43
◇ Drive gain adjustment	44
◇ Drive gain adjustment	44
4 RECEIVE AND TRANSMIT	45
■ Functions for CW operation	45
◇ About CW reverse mode	45
◇ About CW pitch control	45
◇ CW sidetone function	45
◇ APF (Audio Peak Filter) operation	46
■ Electronic keyer functions	47
◇ Memory keyer screen	48
◇ Editing a memory keyer	49
◇ Contest number set mode	50
◇ Keyer set mode	51
■ RTTY (FSK) operation	53
◇ About RTTY reverse mode	54
◇ Twin peak filter	54
◇ Functions for the RTTY decoder indication	55
◇ Setting the decoder threshold level	55
◇ RTTY memory transmission	56
◇ Automatic transmission/reception setting	56
◇ Editing RTTY memory	57
◇ RTTY decode set mode	58
◇ Data saving	60
■ PSK operation	61
◇ About BPSK and QPSK modes	62
◇ Functions for the PSK decoder indication	63
◇ Setting the decoder threshold level	63
◇ PSK memory transmission	64
◇ Automatic transmission/reception setting	64
◇ Editing PSK memory	65
◇ PSK decode set mode	66
◇ Data saving	68
■ Repeater operation	69
◇ Repeater access tone frequency setting	69
■ Tone squelch operation	70
■ Data mode (AFSK) operation	71
■ Spectrum scope screen	72
◇ Center mode	72
◇ Fixed mode	73
◇ Mini scope screen indication	74
◇ Scope set mode	74
■ Preamplifier	79
■ Attenuator	79
■ RIT function	80
◇ RIT monitor function	80
■ AGC function	81
◇ Selecting the preset value	81
◇ Setting the AGC time constant preset value	81
■ Twin PBT operation	82
■ IF filter selection	83
◇ IF filter selection	83
◇ Filter passband width setting (except FM mode)	83
◇ Roofing filter selection	84
◇ DSP filter shape	84
◇ Filter shape set mode	85
■ Dualwatch operation	86
■ Noise blanker	88
◇ NB set mode	88
■ Noise reduction	89
■ Dial lock function	89
■ Notch function	90
■ Autotune function	90
■ VOX function	91
◇ Using the VOX function	91
◇ Adjusting the VOX function	91
■ Break-in function	92
◇ Semi break-in operation	92
◇ Full break-in operation	92
■ Speech compressor	93
■ Transmit filter width setting	93
■ ⊿TX function	94
◇ ⊿TX monitor function	94
■ Monitor function	94
■ Split frequency operation	95
■ Quick split function	96
◇ Split lock function	96
5 VOICE RECORDER FUNCTIONS	97
■ About digital voice recorder	97
■ Recording a received audio	98
◇ Basic recording	98
◇ One-touch recording	98
■ Playing the recorded audio	99
◇ Basic playing	99
◇ One-touch playing	99
■ Protect the recorded contents	100
■ Erasing the recorded contents	100
■ Recording a message for transmit	101
◇ Recording	101
◇ Confirming a message for transmit	101
■ Programming a memory name	102
■ Sending a recorded message	103
◇ Transmit level setting	103
■ Voice set mode	104
■ Saving a voice message into the USB-Memory	105
◇ Saving the received audio memory	105
◇ Saving the TX memory	105
6 MEMORY OPERATION	106
■ Memory channels	106
■ Memory channel selection	106
◇ Using the [▲]/[▼] keys	106
◇ Using the keypad	106
■ Memory list screen	107
◇ Selecting a memory channel using the memory list screen	107
◇ Confirming programmed memory channels	107
■ Memory channel programming	108
◇ Programming in VFO mode	108
◇ Programming in memory mode	108
■ Frequency transfers	109
◇ Transferring in VFO mode	109
◇ Transferring in memory mode	109
■ Memory names	110
◇ Editing (programming) memory names	110
■ Memory clearing	110
■ Memo pads	111
◇ Writing frequencies and operating modes into memo pads	111
◇ Calling up a frequency from a memo pad	111
7 SCANS	112
■ Scan types	112
■ Preparation	112
■ Scan set mode	113
■ Programmed scan operation	114
■ ⊿F scan operation	114
■ Fine programmed scan/Fine ⊿F scan	115
■ Memory scan operation	116
■ Select memory scan operation	116
■ Setting select memory channels	117
◇ Setting in scan screen	117
◇ Setting in memory list screen	117
◇ Erasing the select scan setting	117
■ Tone scan	118
8 ANTENNA TUNER OPERATION	119
■ Automatic antenna selection	119
■ Antenna tuner operation	120
◇ Tuner operation	120
◇ Manual tuning	120
■ Optional external tuner operation	121
9 CLOCK AND TIMERS	122
■ Clock set mode	122
■ Daily timer setting	123
■ Setting sleep timer	124
■ Timer operation	124
10 SET MODE	125
■ Set mode description	125
◇ Set mode operation	125
◇ Screen arrangement	126
■ Level set mode	127
■ ACC set mode	131
■ Display set mode	133
■ Others set mode	135
■ USB-Memory set menu	143
◇ USB-Memory set screen arrangement	143
■ File loading	144
◇ Load option set mode	145
■ File saving	146
◇ Save option set mode	147
■ Changing a file name	148
■ Deleting a file	149
■ Unmounting USB-Memory	149
■ Formatting the USB-Memory	150
11 MAINTENANCE	151
■ Troubleshooting	151
◇ Transceiver power	151
◇ Transmit and receive	151
◇ Scanning	152
◇ Display	152
◇ Format USB-Memory	152
■ Main dial brake adjustment	152
■ SWR reading	153
■ Screen type and font selections	153
■ Frequency calibration (approximate)	154
■ Opening the transceiver’s case	155
■ Clock backup battery replacement	155
■ Fuse replacement	156
◇ DC power cable fuse replacement	156
◇ Circuitry fuse replacement	156
■ Resetting the CPU	156
■ About protection indications	157
■ Screen saver function	157
12 CONTROL COMMAND	158
■ Remote jack (CI-V) information	158
◇ CI-V connection example	158
◇ Data format	158
◇ Command table	159
◇ Data content description	164
13 SPECIFICATIONS AND OPTIONS	167
■ General	167
■ Transmitter	167
■ Receiver	167
■ Antenna tuner	167
■ Options	168
14 UPDATING THE FIRMWARE	169
■ General	169
■ Caution	169
■ Preparation	170
◇ Firmware and firm utility	170
◇ File downloading	170
■ Firmware update	171
15 CE	173

Match case Limit results 1 per page

■

Notch function

Th±s transce±ver has auto and manual notch func-

t±ons.

The auto notch funct±on uses DSP to automat±cally

attenuate beat tones, tun±ng s±gnals, etc., even ±f they

are mov±ng. The manual notch can be set to attenu-

ate a frequency v±a the

[NOTCH]

control.

The auto notch can be used ±n SSB, AM and FM

mode.

The manual notch can be used ±n SSB, CW, RTTY,

PSK and AM modes.

➥

Push

[NOTCH]

to toggle the notch funct±on

between auto, manual and OFF ±n SSB and AM

modes.

•

E±ther auto or manual notch funct±on can be deact±-

vated ±n others set mode. (p. 132)

➥

Push

[NOTCH]

to turn the manual notch funct±on

ON and OFF ±n CW, RTTY, PSK modes.

➥

Push

[NOTCH]

to turn the auto notch funct±on ON

and OFF ±n FM mode.

•

The ±nd±cator on th±s sw±tch l±ghts green when the auto

or manual notch funct±on ±s ON.

•

When the manual notch funct±on ±s ON, push and hold

[NOTCH]

for 1 sec. to select the notch f±lter w±dth for

manual notch from w±de, m±ddle and narrow.

•

Set to attenuate a frequency for manual notch v±a the

[NOTCH]

control.

• “

” appears when auto notch ±s ±n use.

• “

” appears when manual notch ±s ±n use.

Wh±le tun±ng the manual notch, no±se may be

heard. Th±s comes from the DSP un±t and does not

±nd±cate an equ±pment malfunct±on.

■

Auto tune function

<MODE> CW/AM

The automat±c tun±ng funct±on tunes the d±splayed fre-

quency automat±cally when an off-frequency s±gnal ±s

rece±ved w±th±n the range ²500 Hz (CW) or ²5 kHz (AM).

Th±s funct±on ±s act±ve wh±le ±n CW or AM mode ±s selected.

➥

Push

[AUTO TUNE]

to toggle the auto tune func-

t±on ON or OFF.

•

“

” bl±nks when auto tune funct±on ±s act±-

vated.

•

After 2 sec. has passed, the auto tune funct±on stops

tun±ng automat±cally even ±t’s st±ll off-frequency.

IMPORTANT!

When rece±v±ng a weak s±gnal, or rece±v±ng a s±g-

nal w±th ±nterference, the automat±c tun±ng funct±on

may tune the rece±ver to an undes±red s±gnal.

NOTE:

The automat±c tun±ng funct±on does not

act±ve on the sub band.

[NOTCH]

control

NOTCH

• Auto notch indication

Appears

• Manual notch indication

Appears

Unwanted tone frequency

Desired

signal (AF)

Desired

signal (AF)

Particular frequency is attenuated

Auto notch OFF

Auto notch ON

AUTO

TUNE

Appears

RECEIVE AND TRANSMIT